How to set up the ASUS motherboard microphone when there is no sound?

php editor Xiaoxin will introduce to you how to set up the ASUS motherboard microphone without sound. When you use an ASUS motherboard, if you find that there is no sound from the microphone, it may be due to some setting issues. First, you can check if the microphone is properly connected to the microphone jack on the motherboard. Secondly, you can go into the system settings and confirm whether the microphone volume has been muted or turned down. In the meantime, you can also try updating the sound card driver to resolve possible driver issues. If the issue is still not resolved, it is recommended to contact ASUS official technical support for further troubleshooting and solutions.

How to set up the ASUS motherboard microphone if there is no sound?

Causes and solutions for no sound from the ASUS motherboard microphone

Method 1:

1. We open "Control Panel" → "Hardware and Sound".

　2. Then open the management audio device.

　3. In the "Sound" interface, we switch to the "Recording" tab and double-click "Microphone".

　4. Click to switch to the "Level" tab to adjust the microphone volume to the maximum. If the microphone sound is not loud enough, we can also set the microphone to strengthen.

　5. Pay attention to whether there is a "mute" option.

　6. If the microphone is muted and the mute is turned off

What should I do if the ASUS motherboard cannot light up, a common problem?

1. There is generally no compatibility between the motherboard and the graphics card. As long as the interfaces are the same, they can be lit.

2. Check whether the signal cable of the monitor is connected to the graphics card output interface. If the connection is correct, try replacing a cable with better quality.

3. It may also be caused by poor contact between the graphics card and the motherboard. When the graphics card is re-inserted and unplugged, the golden finger part must be completely in contact with the PCI slot of the motherboard.

4. The monitor signal source must be switched correctly. Some monitors have an AUTO icon in the lower right corner. Click on it.

5. If the graphics card has an auxiliary power supply line, it needs to be connected properly. It is recommended to use some good quality brand power supply as much as possible. If you have tried the above methods and still cannot light up, it is recommended to contact the seller to replace or repair the graphics card.

There is no sound from the front panel of the ASUS motherboard. How do I set it in the BIOS?

If you have connected the front panel audio interface on your ASUS motherboard, but you cannot hear the sound when using the computer, you can try to check the following options in the BIOS settings:

Confirm the sound card Already enabled: In BIOS settings, find the Advanced option, then Onboard Devices Configuration or similar. In this menu, make sure the "Onboard Audio Controller" option is enabled. If this option is disabled, select the "Enabled" option, then save changes and exit the BIOS.

Check the front panel connections: In the BIOS setup, find the Advanced option, then Front Panel or similar option. In this menu, make sure that the front panel audio interfaces are connected correctly. You can check the polarity and order of the front panel audio interfaces in this menu.

Adjust audio output: In the BIOS settings, find the "Advanced" option, then "Audio" or a similar option. In this menu, you can try to adjust the settings of the audio output, such as selecting other output options, or adjusting parameters such as volume and gain to ensure that the audio is output normally.

It should be noted that different models and BIOS versions of ASUS motherboards may be different. The above steps are for reference only. If you still cannot solve the problem, please refer to the motherboard manual or contact ASUS technical support for more detailed help.

What should I do if there is no sound from the front headphone jack on my ASUS motherboard?

There is no sound from the front headphone jack. Solution:

Check whether the front headphone plug-in board is connected to the motherboard.

Enter the control panel, click Realtek HD Audio Configuration, Audio I/O, Analog Rear Panel, click the small wrench, check Disable Front Panel and then restart.

If it still doesn’t work, control panel==>Sound Effect Manager (or Soundeffect Manager)==>jack sensing (or interface sensing)==>Click Start, and the software will automatically identify the device .

If it still doesn’t work, click the small hammer icon in the interface to perform manual settings and select the name of the device connected to the interface. Generally, the blue and green ports are for headphone speakers, and the red ports are for microphone software and speaker sets. Status tab, click UAJ Auto in the back panel bar, turn on manual mode, and then perform device settings, the method is the same as described in the previous paragraph.

Why is there no sound behind the motherboard?

1. Check whether the connection between the host and the speaker is loose or disconnected, whether the speaker power is on, and whether the speaker's volume adjustment knob is turned down to the minimum.

　2. For an independent sound card, check whether the sound card is in good contact with the motherboard slot. You can unplug and insert the sound card again.

　3. Open "Device Manager" to check if there is any problem with the sound card driver installation. Solution: Right-click "My Computer" on the desktop → select "Properties" → pop up the "System Properties" window → select the "Hardware" page → press the "Device Manager (D)" button → pop up the "Device Manager" window → Check whether there is "!" or "?" in front of "Sound, Video, and Game Controller" or "Multimedia Audio Controller". If it indicates that the sound card driver is damaged, please find the sound card's driver disk and reinstall the driver (if the sound card If it is integrated into the motherboard, then the driver is in the motherboard's driver CD).

ASUS motherboard sound settings?

Describe the detailed symptoms clearly. The Realtek HD driver needs to be set up: Open the driver management interface-"Audio IO-" Simulation bar, you can see a small wrench icon to the right of these two words, click to open the settings dialog box and modify it item by item to see the situation

Asus motherboard does not alarm if no memory module is inserted?

You should first remove the memory module and then start it up. If the motherboard is not damaged and becomes bricked, it will definitely trigger an alarm. If you still don’t hear the alarm, it means that the buzzer of your motherboard is not connected properly.

The buzzer is a small speaker, some are big or small, the small one is as big as a few pills stacked up, and the big one is as big as an egg. The common feature is the entanglement of two threads: one red and one black.

Under normal circumstances, the buzzer should be connected to the interface. The interface is usually next to the front panel interface (F_PANEL) (you can find it along the power supply line), marked SPEAKER (some abbreviated as SPK). ) of the four needles is it.

If you don’t have a buzzer, buy one. Taobao sells one for 1 yuan.

The reason why I know so clearly is because my previous computer could not be turned on because I could not hear the alarm sound and I misdiagnosed it. Later I found out that there was no buzzer installed at all.

The above is the detailed content of How to set up the ASUS motherboard microphone when there is no sound?. For more information, please follow other related articles on the PHP Chinese website!