What should I do if Gigabyte keeps automatically entering the bios when I turn it on?

php editor Strawberry will answer for you: "What should I do if Gigabyte keeps automatically entering the BIOS when booting?" This is a problem that many computer users often encounter. It may be confusing and annoying when the computer cannot start the system normally after being turned on, but stays in the BIOS interface. But don’t worry, there are some simple ways to fix this problem. Below, I will introduce you to several common solutions to help you start your computer system smoothly.

What should I do if Gigabyte keeps automatically entering bios when booting?

Solution:

1. After entering the Bios interface, press the direction key → switch to the "Bios" menu page;

2. Then use the direction key ↓ to select " Secure Boot" option, change its status to "Disabled";

3. Then change the "CSM Support" option status to "Enaled", press the "F10" key to save or select the save button, and exit Just Bios.

What should I do if I turn on Gigabyte and enter bios?

The BIOS setup interface automatically enters after booting. There are generally two common reasons.

First, the operating system is damaged and the boot fails.

Second, it is a hardware failure and the hard disk cannot be detected. Usually the hard disk is damaged or not connected properly. Check the BIOS hardware detection. If the hard disk is displayed, it is the former. Just reinstall the system. If the hard disk is not displayed, it is the latter. Please check the hard disk data cable and power cable.

What should I do if I boot up Gigabyte h610 and enter the BIOS?

To enter the bios of Gigabyte h610, you can follow the following steps:

1. First turn off the computer and plug in the keyboard and mouse.

2. Press the power button and wait for the computer to start.

3. When the computer starts, press the Del key or the F2 key, depending on which key your computer uses.

4. Keep pressing the key until you see a page that says "Gigabyte", "Gigabyte" or a logo related to that manufacturer.

5. Once you enter the Gigabyte h610 bios interface, you can use the arrow keys and Enter key on the keyboard to browse and change settings.

6. If you want to exit bios and continue booting the computer, just press the Esc key, then save the changes and exit.

Please note that due to different computer and device configurations, the methods of entering bios are also different. If you cannot enter the bios of your Gigabyte h610 after following the above steps, you can try to check Gigabyte's user manual or contact technical support for help.

The Gigabyte board enters the bios as soon as it is turned on. How do I enter the system?

In this case, it is because uefi is turned on. If you want to return to the original startup mode

1. Open csm in bios and open legacy in startup mode (my motherboard is not Gigabyte, but it is basic The options are the same)

2. Enter pe, change the partition format to mbr, and then install it in the previous way.

Does Gigabyte automatically enter the BIOS when it boots up?

Problem analysis: The computer automatically enters the motherboard CMOS interface when it is turned on. If human error is excluded (you can press the ESC key to exit), it means that the computer failed to pass the power-on self-test. Generally, the CMOS parameters are incorrect or the hardware is faulty. . Common phenomena include battery failure, configuration errors, poor memory or hard disk contact, etc., which need to be investigated one by one.

Solution:

1. Battery failure: causing the computer to call CMOS default parameters. If they are inconsistent with the local hardware environment, the computer cannot start normally. You can purchase the motherboard battery to replace it, then turn on the computer and press the DEL key (F2 or other designated hotkeys for notebooks) to enter the CMOS interface, reset the correct parameters, and finally press F10 to save, exit and restart.

2. Configuration error: This situation may also occur because the manually configured CMOS parameters are inconsistent with the local hardware environment. Under normal circumstances, you can press the F1 key to skip non-fatal errors and start the computer directly according to the white text prompt information on the black background, or press the DEL key to enter CMOS, then press F9 to load predefined parameters or select Load Optimized Defaults (Load Optimized Defaults). Performance defaults) or Load Fail-Safe Defaults (load fail-safe defaults), and then press F10 to save, exit and restart.

3. Hardware failure: If the above operations are invalid, it means there is a problem with the hardware. Generally, the memory and hard disk are in poor contact or the hard disk master boot record is damaged. You need to re-insert the memory or hard disk, or repair the hard disk master boot record. Or reinstall the system or replace the hard drive.

The above is the detailed content of What should I do if Gigabyte keeps automatically entering the bios when I turn it on?. For more information, please follow other related articles on the PHP Chinese website!