How to assemble a mobile phone radiator? Is it necessary to install a radiator when assembling a computer?

Is it necessary to install a radiator when assembling a computer? How to assemble a mobile phone radiator? These questions trouble many technology enthusiasts. PHP editor Banana brings you detailed answers to help you gain an in-depth understanding of the mysteries of computer cooling and mobile phone radiator assembly.

How to assemble a mobile phone radiator?

Hello, here are some steps to assemble a mobile phone radiator:

1. First, prepare the radiator and mobile phone you need to use.

2. Peel off the back of the radiator to expose the heat sink.

3. Place the heat sink on the back of the phone, making sure the heat sink is in close contact with the back of the phone.

4. If the radiator is equipped with a fan, plug the fan into the socket on the radiator.

5. If the radiator is equipped with a USB interface, plug the USB interface into the charging port of the mobile phone.

6. Turn on the phone radiator and start using it.

It should be noted that there may be differences in mobile phone radiators of different brands and models. It is recommended to refer to the product manual for specific assembly steps. At the same time, you also need to follow the product instructions when using a mobile phone radiator, and do not overuse or use it improperly to avoid damage to the mobile phone.

Is it necessary to install a radiator when assembling a computer?

The radiator must be installed. The specific steps are as follows:

1. One computer. Here is the chassis with the cover removed. You can see the CPU lying quietly on the motherboard.

2. The radiator has been removed here. Use toilet paper to wipe out the remaining silicone grease on the radiator plate. (If it is a newly purchased radiator, it is a clean heat sink and does not need to be wiped).

3. Inject tube-type silicone grease, aim at the center of the CPU, and squeeze out a large amount of silicone grease. It must be placed in the center and do not apply it to the motherboard circuit board (note: there is a better quality silicone grease with good thermal conductivity, but it contains metal particles, so do not apply it to the motherboard, otherwise there will be serious consequences ) 4. The silicone grease has been applied and is waiting for the radiator to be installed. 5. Remember to press it gently so that there will be no air on the heat dissipation contact surface, thus not affecting heat dissipation. This is it installed.

How to choose a CPU cooler when building a computer by yourself? CPU: i38100?

I3 8100 is a 14mn process CPU with a main frequency of 3.6Ghz, LGA 1151 interface, power of 65W, and the heat is not very large. If it is not used normally, just use the original INTEL radiator. , if you want to use it overclocking, it is recommended to change to a four-heat pipe radiator, the price is between 40-80 yuan.

How to assemble a computer mouse?

The steps are as follows:

1. First, prepare all the accessories of the wireless mouse, including: a wireless mouse, 2 batteries matching the wireless mouse, and a USB plug-in for the mouse.

2. The next step is to install the mouse battery. First, gently open the mouse cover. Note: Just lift it gently from the high-curved tail of the mouse. Do not lift it from the scroll wheel (left and right buttons) to avoid damaging the mouse.

3. After opening the mouse cover, you can see that there are two battery slots on the left and right inside. The above prompts the battery installation direction of the positive and negative poles. According to this prompt, insert the 2 batteries and install them.

4. After installing the battery, close the mouse cover.

5. Next, find the notebook USB socket and insert the USB plug-in for the mouse into it.

6. At this time, press the computer power button to turn on the computer. Then turn the mouse over, turn it on, and the prompt light will light up. Note: "I" means open, O means closed.

How to make money by assembling computers?

Assembling computers means assembling them for others to earn the price difference of accessories and the corresponding labor costs.

In the past, the profit from assembling computers was relatively high. Now the prices are very transparent. Most of the money earned is labor costs. For a computer, you could earn four or five hundred in the past, but now two or three hundred is pretty good. , but if the quantity is large, it is still good. You have to think carefully to see if it is suitable for you.

How to assemble a computer neatly

I got a new computer after joining the job, and the configuration is pretty good. But every time I use a new computer or reinstall the system, the desktop always becomes a mess after a while. I must change this situation this time. How can this situation be improved? Just do it and think about it, this is not something that can be accomplished overnight.

First of all, to make the desktop look clutter-free, there must not be too many icons on the desktop. I still remember that I had a conceited roommate who had so many desktop icons that he almost filled up his desktop. It looked really bad. Therefore, I have to strictly control the number of icons. Only one column can be left on the desktop and one column is empty. So far, this visual effect is not bad. For some other software you need to use, you can search directly through the lower left corner. It is quite convenient. In fact, it is faster than searching for icons when you fill the desktop with them.

How to assemble a computer keyboard?

1. First of all, we need to understand the structure of the button. If the removed button is x, see what the structure inside is like. Align the direction of the keycap and press it against the bracket.

2. Use a little force and a click sound will appear, indicating that the installation is successful. Next, install the more complicated shift key. The two situations are slightly different. The bracket of the x key is directly connected to the keyboard, while the bracket of the shift key is connected to the keycap.

3. Now you need to remove the white bracket from the keycap. There are three parts in total, two white parts and a small steel wire. The small steel wire is connected to the inside of the keycap and does not need to be removed.

4. Combine the two white parts into one, and then install the integrated white bracket onto the keyboard. Note that there are buttons on the keyboard. Be careful when installing and remember to pull or pull hard.

How to assemble lenovo computer?

The specific installation steps are as follows

1. CPU installation

The CPU should be put down smoothly, then cover the iron cover, press the iron rod firmly into place, and the CPU installation is completed.

Then apply CPU cooling silicone evenly on the CPU

2. Install the CPU radiator

First, turn the four foot pins to the opposite direction of the arrow above. Then align the four empty spots on the motherboard and press hard to complete the installation of one position. Repeat four times.

If you want to disassemble the radiator, turn the four pins in the direction of the arrow above, then pull hard, repeat four times to disassemble.

3. The installation of the memory is very easy. Align the memory and the bumps on the memory slot, and press it with left/right force respectively. When you hear a small "pop" sound, the left/right slot will automatically open. , and then press the other side in the same way.

4, Power supply installation

Install the four screws of the power supply

5, Motherboard installation Use a screwdriver to press the screws into the reserved screw holes to fix the motherboard.

6. Hard drive installation

You can choose the bay to install the hard drive. The general principle is to install it in the middle to ensure more heat dissipation. Four screws are installed. If you are lazy, you can also install two diagonally. .

7. Graphics card installation

Nowadays, independent graphics cards are not required to be installed. The CPU or motherboard has integrated graphics cards, so it is no problem to meet the basic requirements. Installing the graphics card is not difficult. Just remove the chassis baffle, insert it into the PCI-E slot, and then tighten the screws. If the motherboard has multiple PCI-E

8, motherboard wiring

1. Motherboard power supply/CPU auxiliary power supply: align the bayonet and connect

2. Front audio and front USB: align Plug in the fool-proof interface

3. The hard disk light, power light, power button, and restart button are installed according to the motherboard markings (color wire positive, black and white wire negative)

HDD LED represents the hard disk light , POWER LED is the power light, RESET SW is the reset button, POWER SW is the switch, and PC SPEAKER is the PC speaker.

4. Hard drives now basically have SATA interfaces. Just connect the SATA power cable (5PIN flat cable) and data cable.

5. Don’t forget to connect mid-to-high-end graphics cards. How to assemble the computer configuration using 6PIN or 8PIN auxiliary power supply?

1. Assembling a computer configuration requires certain skills and knowledge. 2. First, you need to clarify your needs and budget, and determine the purpose and performance requirements of the computer to be assembled. Then, select the appropriate hardware components such as motherboard, processor, memory, hard drive, graphics card, etc., and ensure compatibility between them. Next, install these hardware components into the computer chassis and connect the corresponding power cables, data cables, etc. Finally, install the operating system and necessary drivers. 3. Assembling a computer configuration is a relatively complex process that requires certain experience and skills. During the assembly process, you can also make some optimizations and adjustments based on personal needs, such as selecting a suitable radiator, adding additional fans, etc. Additionally, it's helpful to know some common troubleshooting methods.

How to assemble a computer host?

The assembly steps are as follows:

1: Tools and components. First of all, you need to prepare the corresponding tools, such as screwdrivers and screwdrivers. Usually, simple tools are given when you purchase the case. At the same time, you must also prepare various components of the host such as motherboard, graphics card, memory stick, CPU, power supply, chassis, etc.

　　二: Install the CPU. The installation of the host starts with the CPU. Unpack the motherboard and CPU packaging boxes, take out the motherboard, find the location of its CPU interface, and press the lever down to open it. Then take out the CPU and align it for installation. Be gentle. Be slow and careful to avoid bending the CPU pins.

Three: Install a cooling fan. If it is a boxed CPU, it will come with a cooling fan, which can be installed on the motherboard together with the CPU. If you purchase a separate cooling fan yourself, you need to apply silicone grease to the CPU before installing the fan.

Four: Install the power supply. Put the motherboard with the CPU installed next to it, first disassemble the case and then install the power supply. Here you need to use a screwdriver to tighten the screws to fix the power supply in the case, and remove some cards on the back of the case to facilitate the installation of the motherboard later.

Five: Install the motherboard. After the power supply is installed, you can fix the motherboard inside the chassis, determine the installation direction, and then use screws to fix the motherboard. Be careful not to make a mistake. You can confirm it by looking at the slot of the graphics card. It is generally easier to find the direction.

Six: Install the memory module. Take out the memory stick. If it is two memory sticks, it is recommended to install it in slots 1-3. If it is a single memory stick, install it in the second slot. After the memory stick is installed, press the fixing rings on both sides to ensure The memory stick will not loosen.

Seven: Install the graphics card. Then take out the graphics card, align it with the slot and install it. At the same time, use a screwdriver to fix the graphics card on the chassis to ensure that the graphics card does not shake left and right, and the interface of the graphics card needs to face the outside of the chassis.

Eight: Wiring. After these are installed, you can observe the layout of the chassis, and then start wiring. In principle, it is better to be as simple as possible. You need to connect the graphics card, motherboard and power supply. At the same time, the motherboard may also need to be connected to the graphics card. Nine: Others. If there is an optical drive on the host, you need to install it on the upper part of the chassis and fix it with a screwdriver. Then connect the power supply and motherboard. After all the cables are connected, you can connect the monitor to test whether it can boot normally.

The above is the detailed content of How to assemble a mobile phone radiator? Is it necessary to install a radiator when assembling a computer?. For more information, please follow other related articles on the PHP Chinese website!