How to connect the power cord when assembling a computer?

During the process of assembling a computer, how to connect the power cord correctly is a common problem. PHP editor Xinyi will introduce the correct connection method of power cord in detail in this article to help everyone easily deal with assembly problems.

How to connect the power cord of the assembled computer?

When assembling the computer power cord, you need to connect the power cord to the power supply and the computer host. The following are general steps:

1. Disconnect the power supply: Make sure the power supply and computer host are powered off, and unplug the power plug.

2. Connect the power supply: Insert the plug of the power cord into the corresponding socket of the power supply. The socket on the power supply is usually located on the back of the power supply and has a specially shaped slot to ensure that the plug is connected correctly.

3. Connect the host: Look for the power interface on the back of the computer host, usually located on the top or bottom of the host. Plug the other end of the power cord into the power socket of the computer host.

4. Fix the cables: Use cable ties or wire harnesses to fix the power cords around the host to ensure that the cables are neat and safe.

5. Check the connection: Make sure the power cord is tightly connected to the power supply and computer host socket without looseness.

6. Repower the computer: Insert the power plug into the power socket and turn on the power switch to power the computer.

When connecting the power cord, please make sure to choose a power supply that meets the hardware requirements of your computer, and ensure that the power cord is properly installed and assembled to ensure a secure and safe connection. If you encounter any problems during connection, it is recommended to refer to the manual of the power supply or computer host, or seek professional help. Also, be careful when assembling the power cord and make sure to follow relevant safety operating procedures to protect your own safety.

How to plug in the power cord when assembling a computer?

1. Take out the motherboard, remove the CPU and install it, fix the fan, plug in the memory and put it away.

2. Remove the covers on both sides of the chassis, install the power supply, and screw the motherboard tray screws in the chassis to the designated position.

3. Handle the motherboard baffle according to the interface position, snap it into the chassis back bezel, put the motherboard correctly into the chassis, and gently tighten the screws. For independent graphics, break off the small PCI-E baffle, insert the graphics card and secure it with screws.

4. Plug in the 24 4-pin power cord. If the 4-pin cord is too long, tie it into a knot.

5. Separate the front USB and audio jack cables with USB and AUDIO letters on the back from the chassis, and insert them into the USB pin slot and AUDIO pin slot of the motherboard respectively. Both are to prevent mis-insertion. The USB pin slot is usually in the lower right corner of the motherboard, and there is a USB mark under the pin slot. The AUDIO pin slot is generally located in the middle and lower left side of the motherboard.

6. Knot the switch, restart, hard disk indicator light and other wires on the chassis. Generally, this type of plug on the motherboard is adjacent to the USB. In the lower right corner of the motherboard, there are letters marking the corresponding plugs on the motherboard, such as HDLED. is the hard disk indicator light, RST is the cold start, POW-SW is the startup, SPEAKER is the alarm horn, and POW-LED is the power indicator light. Just plug them in one by one.

7. Remove the baffle at the optical drive position of the chassis (the card head can be pushed out from the back and removed). Put the optical drive in and secure it with screws.

8. Take out the optical drive and hard disk data cable. If it is a parallel port data cable, please confirm that there is an IDE interface on the motherboard. The serial port cable is generally longer. After forming a spiral shape with your fingers, you can insert it into the motherboard serial port port in sequence, and then plug in the optical drive and hard disk power cables.

9. Use tying thread to gather and fix the messy threads appropriately. Install the side covers in sequence. You're done, the next step is to partition the hard drive and build the system.

Purely personal experience, let’s discuss the shortcomings together. Reproduction is prohibited.

How to connect the power circuit of the assembled computer?

1. Take out the motherboard, remove the CPU and install it, fix the fan, plug in the memory and put it away.

2. Remove the covers on both sides of the chassis, install the power supply, and screw the motherboard tray screws in the chassis to the designated position.

3. Handle the motherboard baffle according to the interface position, snap it into the chassis back bezel, put the motherboard correctly into the chassis, and gently tighten the screws. For independent graphics, break off the small PCI-E baffle, insert the graphics card and secure it with screws.

4. Plug in the 24 4-pin power cord. If the 4-pin cord is too long, tie it into a knot.

5. Separate the front USB and audio jack cables with USB and AUDIO letters on the back from the chassis, and insert them into the USB pin slot and AUDIO pin slot of the motherboard respectively. Both are to prevent mis-insertion. The USB pin slot is usually in the lower right corner of the motherboard, and there is a USB mark under the pin slot. The AUDIO pin slot is generally located in the middle and lower left side of the motherboard.

6. Knot the switch, restart, hard disk indicator light and other wires on the chassis. Generally, this type of plug on the motherboard is adjacent to the USB. In the lower right corner of the motherboard, there are letters marking the corresponding plugs on the motherboard, such as HDLED. is the hard disk indicator light, RST is the cold start, POW-SW is the startup, SPEAKER is the alarm horn, and POW-LED is the power indicator light. Just plug them in one by one.

7. Remove the baffle at the optical drive position of the chassis (the card head can be pushed out from the back and removed). Put the optical drive in and secure it with screws.

8. Take out the optical drive and hard disk data cable. If it is a parallel port data cable, please confirm that there is an IDE interface on the motherboard. The serial port cable is generally longer. After forming a spiral shape with your fingers, you can insert it into the motherboard serial port port in sequence, and then plug in the optical drive and hard disk power cables.

9. Use tying thread to gather and fix the messy threads appropriately. Install the side covers in sequence. You're done, the next step is to partition the hard drive and build the system.

Purely personal experience, let’s discuss the shortcomings together. Reproduction is prohibited.

How to connect the motherboard power cord to the assembled computer?

There are close friends in the sea, and we are neighbors in the world.

The window contains Qianqiu snow of Xiling, and the door is docked with a ship thousands of miles away from Dongwu.

The country is broken by mountains and rivers, and the spring vegetation of the city is deep.

Living deep in Foujia City, spring is gone and summer is still clear.

Do I need to buy the power cord separately when assembling a computer?

Don’t buy it separately

You don’t need to buy the thread yourself. When you buy a hard drive, the hard drive comes with its own hard drive cable; the power supply comes with various interface cables; the motherboard also comes with its own hard drive cable, and the chassis comes with its own signal cable, front USB port cable, and power cable. In other words, everything you buy comes with a cable, so there is no need to buy additional cables. If it doesn't come with a cable, it's usually taken away by the seller.

When assembling a computer, how to connect the computer switch power cord to the computer motherboard?

The one marked power sw is the power-on pin, which is divided into two, which are positive and negative. Just insert them according to the corresponding positions on the motherboard. There is no care when plugging in. Just plug the positive and negative poles in reverse and then reverse them. Generally, it will not harm the computer.

How many power cords are there in assembling the computer and are they plugged into the power strip?

The computer’s power cord includes the host’s power cord that needs to be plugged into the power socket, the monitor’s power cord that needs to be plugged into the socket, and the audio’s power cord that needs to be plugged into the power socket! The basic one is three!

How much does it cost to assemble a computer?

Graphics card rtx2060 2500 yuan (supports ray tracing)

cpu R5 3600 1400 yuan

Motherboard: B450 600 yuan

m.2 Solid state drive 500G 600 Yuan

4T mechanical hard drive 600 yuan

Main case with fan + power supply 600w 500 yuan

Memory stick 8G two, 500 yuan

Keyboard and mouse 100 Yuan

List for assembling a computer?

Assembling a computer does require a checklist, because when we assemble the computer, after determining the configuration and operation requirements of the computer, we can purchase some suitable motherboards online, and then determine the power supply, graphics card and other configurations based on the motherboard. If you ask, just make a list and ask the computer factory or dealer directly to buy it

Assemble the computer, okay?

Assembling a computer can have some benefits, such as:

1. Customized configuration: Assembling a computer can choose the appropriate hardware configuration according to personal needs, and you can choose more based on your own purpose and budget. Suitable components.

2. Cost-effectiveness: Assembling a computer is more cost-effective than purchasing a brand-name machine. You can save costs by choosing hardware with higher cost-effectiveness.

3. Upgradeability: Assembling a computer is usually easier to upgrade the hardware. The hardware can be upgraded or replaced at any time as needed to improve the performance of the computer.

4. High degree of freedom: When assembling a computer, you can choose the appearance design, color matching, etc. according to your personal preferences, and you can create a unique computer.

However, there are also some challenges and risks in assembling a computer, such as requiring certain professional knowledge and skills, choosing inappropriate hardware that may cause compatibility issues or poor performance, possible risks during the assembly process, etc. . Therefore, if you do not have enough experience and skills, or do not know much about computer hardware, it may be more suitable to buy a branded machine.

The above is the detailed content of How to connect the power cord when assembling a computer?. For more information, please follow other related articles on the PHP Chinese website!