Swing gate mainboard setting instructions?

php editor Apple brings you the latest swing gate motherboard setting instructions. This manual explains in detail how to correctly set up the swing gate mainboard, allowing you to easily master the operating skills. Whether you are a novice or an experienced user, you can quickly understand the functions and usage of the swing gate mainboard through this article. Following the guidance, you will make better use of the swing gate mainboard and improve the efficiency and security of the access control system.

Swing gate mainboard setting instructions?

First set the controlled gate type (swing gate, double swing gate), and connect the wiring to the gate, whether it is the main board or the slave

machine board, the proximity switch on the left Connect the left position to the left position, the middle one to the zero position, and the right one to the right position (note: the swing gate only has 2 positions, the zero position and the left position, the right position is not used), the person faces the motherboard, the left infrared is connected to the left infrared, and the middle one is connected to the left infrared. The one on the right is connected to the anti-clip, and the one on the right is connected to the right infrared. Connect the motor wires casually, turn on the power, and check which motor direction is wrong, then reverse the motor wires on that side.

Turn board parameter setting instructions:

After the control board is powered on, the LCD screen displays the default state. The default state displays the "working mode" of the control board at this time (swing gate, split swing gate) There are three working modes of gate and swing gate)), as well as parameters such as the number of entrances and exits. There are a total of 5 operation buttons on the control panel, "Menu", "Up", "Down", "OK" and "Cancel".

Button description:

Menu: used to enter menu setting items.

Up: Used to move menu items upward.

Down: Used to move menu items downwards.

Confirm: Used to enter the menu item settings or confirm the current modified value.

Cancel: Used to return to the previous menu or cancel the current operation.

Menu operation:

Press the "Menu" key to enter the password input interface. The default password is: up, up, down, up and down. Enter the 6-digit password and

press "OK" to enter the menu. After entering the menu, press "Up" and "Down" to select a certain function menu and then press "OK".

Why does the exit door not automatically pop up when it is placed low?

1. Directly controlled by the software management background, the signal is transmitted to the gate control main board through TCP/IP or 485 communication and commands it to open.

2. Directly send an I/0 relay signal to the turnstile main board through the license plate recognition camera.

3. Give the gate an opening signal through the remote control.

So what are the reasons why the barrier gate cannot be raised?

1. If the software management background is used to control the gate opening without lifting the pole, it is possible that the signal cannot be sent to the main board of the gate normally, or the heartbeat may be disconnected, or it may be caused by the aging of the network cable itself.

2. If the license plate recognition camera directly sends an I/0 relay signal to the main board of the gate to control the opening of the gate. In this case, the pole cannot be raised. It may be that the license plate recognition camera is not working properly. It may be that the license plate recognition camera is not working properly. The power supply may be faulty, or the angle of the license plate recognition camera may be changed due to external factors, making it unable to capture the license plate normally.

3. Finally, if you use a remote control to control the barrier gate lift, it may be that the remote control is not working properly, there is no battery, etc.

4. If the above situation has been ruled out, you can also check The condition of the barrier gate itself, whether it is due to a malfunction of the barrier gate itself or a problem with its own power supply that causes the barrier gate to fail to operate.

5. Another situation is that there is a problem with the vehicle detector or the ground sensor, resulting in the signal being unable to be triggered, and the camera not receiving the signal to take pictures, resulting in the barrier being unable to raise the pole.

What is the cause of gate machine failure?

Causes of faults and repair methods:

1. Check whether the motor cable is connected well. If the motor cable is connected well, use your hands to mold the tail of the motor to see if the motor is rotating. If it is rotating, explain The motor wires are connected backwards. Reconnect the positive and negative motor wires. If the motor does not rotate, directly connect the 24V power supply to the motor. If the motor still does not rotate, it means the motor is damaged. If the Jiguo motor rotates, it means the motor on the motherboard. There is a problem with the driver, please contact us to replace the motherboard.

2. Check whether the on signal line is dropped, and check whether the on signal indicator light on the motherboard receives an on signal.

3. None of the mainboard indicators are on. Check whether the connection between the switching power supply and the board is normal. If the fuse is damaged, replace the fuse; if the fuse is normal, it means the mainboard is damaged. Replace the mainboard.

The above is the detailed content of Swing gate mainboard setting instructions?. For more information, please follow other related articles on the PHP Chinese website!