Solve the startup problem of Gigabyte z370hd3 motherboard: unable to enter the operating system after installing NVMe

php Editor Youzi, for the problem that the Gigabyte z370hd3 cannot enter the system and is stuck on the motherboard interface after installing nvme, there are several solutions as follows. First, you can try to update the BIOS version of the motherboard. Sometimes the old version of BIOS may not support nvme hard drives. Secondly, check whether the hard drive is connected correctly and make sure that the slot and power cord are not loose. If none of the above methods work, you can try clearing the CMOS by turning off the power, removing the battery, and then pressing and holding the power button for 10 seconds, then reinstalling the battery and restarting the computer. If the problem persists, it is recommended to contact GIGABYTE customer service for more professional help.

I installed nvme on Gigabyte z370hd3, but I can’t enter the system and it’s stuck on the motherboard interface. What should I do?

The hard drive is not broken, it is the fault of nt6oemloader. Now that the hard drive box can be connected, enter PE, delete all partitions, reformat it, and the BIOS will not be stuck, and then reinstall it. It's good that yours can be connected to the hard drive box, but my nvme SSD hard drive cannot be hot-swapped, and I don't know what to do.

How about Gigabyte z370hd3-cf?

Basically considered a beggar’s board. If it is a processor below 9600kf, it is enough, but if you want to overclock, it is best to buy a better motherboard

How to configure the Gigabyte Z370HD3-CF?

GIGABYTE Z370HD3-CF is a motherboard suitable for high-performance computers. You need to pay attention to the following points when configuring:

First of all, you must choose a CPU suitable for the motherboard. It is recommended to choose Intel’s eighth-generation Core processor ;

Secondly, choose a memory module suitable for the motherboard, preferably DDR4 2666MHz or above;

Furthermore, choose a suitable graphics card, it is recommended to choose a graphics card above GTX 1060;

Finally, choose a power supply and chassis suitable for the motherboard. It is recommended to choose a power supply above 600W. The chassis requires good ventilation. The above configuration can meet the needs of most games and applications.

What do the D3V, D3H and HD3 on the back of the Gigabyte motherboard mean?

The D3V, D3H and HD3 on the back of the Gigabyte motherboard are: The letter D means that the motherboard uses all-solid capacitors, where 3 means Speed ​​(transmission, speed) Smart (automatic) Safe (safety) , such as Gigabyte GA-B85M-D3V, and Gigabyte GA-B85M-D3H. Content expansion: 1. Gigabyte GA-B85M-D3V and Gigabyte GA-B85M-D3H both use Micro ATX form factor (small board). What are their differences? Yes: 1. Gigabyte GA-B85M-D3V supports a maximum of 16G memory (2 DIMM slots), 2. The monitor supports DVI and VGA interfaces. Gigabyte GA-B85M-D3H supports a maximum of 32G memory (4 DIMM slots), 3 In addition to supporting DVI and VGA interfaces, the monitor also supports HDMI high-definition interfaces. 2. The letter H should be the abbreviation of High-end in English, indicating that the motherboard is a high-end product among similar products, such as Gigabyte GA- B85-HD3.

3. Therefore, D3H has the highest positioning, stronger expansion functions, best workmanship and power supply; followed by HD3; and finally D3V.

What does motherboard m mean?

M means the small form factor of the motherboard.

The microATX (µATX, mATX or uMTX) motherboard standard was published in December 1997. The size is 9.6 inches × 9.6 inches (24.4cmx24.4cm). Its length is 20% shorter than Standard ATX, which has a standard size of 12×9.6 inches. Due to the reduced length, the maximum number of expansion slots for ATX is reduced from 7 to 4.

mATX is designed to be compatible with ATX. The width and backplane I/O size of both are the same, and the mounting contacts (screws) are also some of those of ATX, so mATX motherboards can be installed in ATX cases.

I have taken a fancy to Gigabyte's Z370HD3 motherboard. Is the quality of this motherboard good?

good.

The Gigabyte Z370 HD3 has a very good experience. It is a motherboard with good performance and high praise rate from users. High cost performance and good workmanship. The Z370 motherboard supports overclocking with this processor. After overclocking, the 8350K single-core performance is pretty good, and the four cores are basically sufficient.

GIGABYTE Z170-HD3 DDR3 motherboard?

The poster is talking nonsense, Z170-HD3 DDR3 large board, 1151 pins, supports sixth and seventh generation CPUs, because i7 7700K integrates DDR3 DDR4 memory controller, no matter which memory you use, it can be used with It doesn’t matter what kind of memory the motherboard uses to support the CPU. For the Z170 motherboard, as long as you refresh Bois to the latest version, it will perfectly support i7 7700K. If you don’t refresh Bois, use i7 6700K and it will perfectly support it.

The above is the detailed content of Solve the startup problem of Gigabyte z370hd3 motherboard: unable to enter the operating system after installing NVMe. For more information, please follow other related articles on the PHP Chinese website!