Solid state drive cannot enter win10 safe mode

Many users encounter system problems and need to enter safe mode when using their computers. Sometimes they encounter more difficult problems, such as being unable to access the solid-state drive. Let’s take a look at the specific solutions below. .

Win10 safe mode cannot enter the solid state drive:

1. Restore the state before the hardware change and check whether the system can start normally.

2. Check whether all cables or expansion cards are connected correctly.

3. Try to reconfigure "PNP/PCI configuration" and "Reset Configuration Data" in the BIOS.

You can also use BIOS options such as "Force Update ESCD" to set it to "Enabled" ”,

Then save and exit. If it can't be started, try setting it to "Disabled" again.

4. Check the motherboard manual for information about the CMOS jumper and clear the CMOS.

Please note: When clearing CMOS settings, you must unplug the host power cord or set the host power switch to off or 0.

5. Disconnect the hard disk connection cable, including the optical drive or other IDE device, and then enter the BIOS settings and select the boot sequence as floppy disk boot. Press F10 to save and exit.

Then put a file in the floppy drive. Create a bootable system disk and check whether the system can start normally.

6. After clearing the CMOS settings, set the "PNP/PCI configuration" option in the CMOS settings to "Enabled",

restart the computer again to update the DMI data, and It is called forced update of ESCD data.

Win10 safe mode cannot enter the solid state drive Reasons:

1. Hardware changes

When the hardware configuration of the host changes, But when we use the POST function, the system cannot recognize the newly added hardware at this time.

will work according to the old configuration. At this time, it will appear that it can be powered on after booting.

But there is no "beep" sound during normal startup, and there is no image display on the monitor, only the sound of the fan rotating.

Another reason is that the newly added hardware has poor compatibility, which leads to the above situation.

2. BIOS settings change

When the BIOS settings are incorrect, such as the memory read and write parameters are incorrectly set, the hard disk mode setting is incorrect,

The onboard sound card and Incorrect settings of the integrated sound card may cause the system to fail to start normally.

3. Hard disk cable connection error

In this case, the hard disk data cable has poor contact, and the poor quality of the data cable causes too many errors when transmitting data.

Data cable Incorrect plugging (the motherboard end and the hard drive end are reversed), the master-slave hard drive jumper is wrong, the hard drive capacity or mode setting is wrong, etc.

4. The contents of the hard disk's main boot area are damaged

When the contents of the hard disk's main boot area are rewritten by other programs or destroyed by viruses, it is also possible that the hard disk partition table has been cleared or artificially set. When it enters the logical lock state, it will crash at this time.

For the boot program of the main boot area of ​​the hard disk is damaged,

We can use the Fdisk/MBR command to repair it,

or use the disk editing function of KV3000 to find it If there is a backup master boot sector program for the other 62 sectors on the 0th track and the 0th side, just restore it to the 0th track, the 0th side and the 0th sector.

It is more troublesome if the partition table is damaged. If the partition table does not have the "80" mark or multiple "80" marks,

or does not have the "55AA" mark, we only need to use the disk editing function of KV3000 to repair it manually.

If it is a logical lock, you need to make a special disk to unlock it. If the partition table is completely destroyed or encrypted, then we can only repartition it.

5. Hard drive failure

Nowadays, the capacity of hard drives is getting larger and larger, and the speed is getting faster and faster, but the quality of hard drives seems to be getting worse and worse.

Currently, there are still hundreds of second-hand hard drives produced in 1994 and 1995 for sale on the market.

But now, the new hard drive that I just bought will have bad sectors or inexplicable data loss within a few days, or it will "bang bang" and stop working.

When the hard disk hardware fails, the above situation will also occur. The hard disk with such problem can recognize the hard disk in CMOS.

The disk recognition goes smoothly, but it cannot enter the system and cannot Partition and format normally.

6. There is a problem with the motherboard

The main problem related to the motherboard is the motherboard's hard disk controller, which causes unstable data transmission and a high error rate.

7. Damage caused by overclocking

If we overclock the computer, it will also crash on the hard disk after booting.

At this time, it is best to check the CPU frequency displayed during the power-on self-test, and then open the chassis to check the actual CPU frequency and whether they are the same.

Especially for CPUs after PIV, their integration level is extremely high. If we use it overclocked,

It is very likely to cause the electrons inside the CPU to decay excessively in a short period of time, causing the CPU to scrapped.

The above is the detailed content of Solid state drive cannot enter win10 safe mode. For more information, please follow other related articles on the PHP Chinese website!