Learn how to disassemble a Mac hard drive

Many friends ask about the mac hard drive disassembly tutorial. This article will provide you with detailed answers and hope to help you. Please read on!

Introduction to how to replace the hard drive of an Apple notebook

Put the newly purchased hard drive into the hard drive box and connect it to the Apple computer. Open Disk Utility.

The specific method is as follows: First, open the back cover of the computer and remove the original hard drive. Then, remove the screws and install them on the new hard drive. Finally, close the back cover of the computer and connect the two computers together using lightning cables.

The specific method is as follows: Put the newly purchased hard drive into the hard drive box and connect it to the Apple computer. Open Disk Utility.

You can add a solid state drive, but you need to pay attention to the compatibility of the solid state drive. As long as the notebook has enough slots, multiple solid-state drives can be added. It is best to go to the official after-sales service to add it to avoid damaging the notebook.

Yes, the hard drive type of MacBook is SSD solid state drive, so you can replace the mechanical hard drive with a solid state drive. However, Apple computers only have one hard drive location, so you cannot add a hard drive, you can only replace the hard drive.

It is recommended that before removing the screws at the bottom of the computer, place them in a small bowl or other container to prevent loss. Then use a tool to pry off the bottom cover to find the hard drive, which is usually held in place by a small piece of plastic. Just remove the screws holding the plastic piece in place.

#How to replace a solid state drive on a mac How to replace a solid state drive on a mac

Therefore, this tutorial will share with you how to replace a solid state drive on a mac. The specific method is as follows: First, remove the eight small screws under the fuselage (at this time, you need to use a small screwdriver specially used to remove marble products).

After the hard disk is installed, you can consider replacing the memory module. After installation is complete, please carefully check whether all screws and buckles are tight. At the same time, you can also take the opportunity to blow away the dust from the fan part.

The specific method is as follows: Put the newly purchased hard drive into the hard drive box and connect it to the Apple computer. Open Disk Utility.

Right-click this computer and select Properties, as shown in the figure below. Click Device Manager in the properties interface, as shown in the figure below. Click on the disk drive in the Device Manager interface, and you will see your newly added SSD, as shown in the figure below. Return to the desktop, right-click this computer and select Manage, as shown in the figure below.

How to replace the hard drive of your Macbook in four simple steps

1. Unscrew the four screws, remove the metal case, and replace it with a new hard drive. Then reinstall it in reverse order, paying attention to tightening the screws. It only takes half an hour at most and is super easy.

2. Press and hold the OPITON button to boot and select Recovery 9. Select Disk Utility and erase the data on the new hard drive first. Be careful not to choose the wrong disk! otherwise? Click the Recovery tab, then select your primary hard drive as the source disk and the new hard drive as the destination disk. Then click Continue, and the copy will be completed in a few minutes.

3. Without disassembling the machine, install the solid state drive into the mobile hard drive box and connect it to the computer. Maybe you noticed that my "mobile hard drive box" is just a small circuit board, which is actually it.

4. Try different data lines to make sure your line is normal. 1Consider replacing the mobile hard drive, maybe the hard drive is broken.

5. My macbook pro 2015 was flooded once before. I have been using it since it was repaired. It is fully sufficient for daily office work. The only problem is that the 256g hard drive capacity is not enough, and it always needs to be deleted after a while. A lot of software. In order to avoid further trouble, I replaced a solid state drive in the past two days.

6. You can only replace the hard drive. The memory is soldered on the motherboard and you cannot add it yourself. Steps to replace the hard drive: Open the back cover, find the hard drive, remove and install it, reinstall the system, OK.

Conclusion: The above is the entire content of the mac hard drive disassembly tutorial compiled by this site for you. Thank you for taking the time to read the content of this site. I hope it will be helpful to you. For more related content, don’t forget to check out Search this site.

The above is the detailed content of Learn how to disassemble a Mac hard drive. For more information, please follow other related articles on the PHP Chinese website!