Some common commands for setting network parameters in Linux

Here are three commands related to network settings:

• ifconfig: Query and set network card and ip, subnet mask and other parameters (net-tools tool needs to be installed first)

• ifup, ifdown: Start and shut down the network interface

• route: View and configure routing information

ifconfig

First look at the ifconfig command

ifconfig [网卡名] [选项]
up、down：启动或关闭该网络接口
mtu：设置mtu值
netmask：设置子网掩码
broadcast：设置广播地址

First look at the first example to view all network cards on the system, just enter ifconfig Just use the command without adding any parameters

# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.2.220  netmask 255.255.255.0  broadcast 192.168.2.255
        inet6 fe80::1733:cf21:906d:57af  prefixlen 64  scopeid 0x20<link>
        ether 00:0c:29:84:5b:d0  txqueuelen 1000  (Ethernet)
        RX packets 9946  bytes 10315936 (9.8 MiB)
        RX errors 0  dropped 3  overruns 0  frame 0
        TX packets 2208  bytes 186213 (181.8 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
  ……

From the output information of this command, we can get a lot of information, such as network card name, IP address, subnet mask, broadcast address, etc.

Let's continue to look at a few examples

# 修改ip地址
# ifconfig eth0 192.168.1.222

You will find that you only modified the IP address, but the broadcast address will also change accordingly.

# 同时修改ip、子网掩码以及mtu值
ifconfig eth0 192.168.2.222 netmask 255.255.240.0 mtu 1000

Please practice with confidence as soon as possible. In the end, you only need to restart the network and it will be restored to the settings of the previous configuration file

ifup ifdown

When we modify the network configuration file /etc/sysconfig/network-scripts/ After eth0, I want to take effect immediately. Then you need to use

ifdown eth0
ifup eth0

In addition to this method, generally we will also use

/etc/init.d/network restart

to restart all network cards.

route

route This command can view the routing table and can also be used to set routes.

View routing information route [-nee]

• -n: Do not display the host name, display it directly with IP, which is faster. This option has many commands about the network.

• -ee: Display more detailed information

# route -n
Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
0.0.0.0         172.19.255.253  0.0.0.0         UG    0      0        0 eth0
169.254.0.0     0.0.0.0         255.255.0.0     U     1002   0        0 eth0
172.19.0.0      0.0.0.0         255.255.0.0     U     0      0        0 eth0

• Destination : Network address

• Genmask: Subnet mask, Destination and Genmask form a network

• Gateway: Gateway address (if displayed is 0.0. 0.0 means that the route is transmitted directly by the local machine, that is, it can be sent directly through the LAN. If the IP address is displayed, it means that the route needs the help of the router (gateway) before it can be sent out.

• Flag: Flag, the common U indicates that the route is enabled, G indicates that the route needs to transmit data packets through an external host.

The above is the detailed content of Some common commands for setting network parameters in Linux. For more information, please follow other related articles on the PHP Chinese website!