Is it common to assemble computer cases? How long is the lifespan of an assembled computer power supply?

When assembling a computer, choosing the right chassis and power supply is crucial. However, many computer enthusiasts have limited knowledge of these issues. This article is brought to you by PHP editor Youzi. It will discuss in detail whether it is universal to assemble a computer case and the service life of the power supply, to help you make a wise choice when assembling a computer.

Is it universal to assemble a computer case?

generic.

is universal, but you should note that there are differences in sizes.

A large motherboard can be used with a large chassis, and a small motherboard can be used in both large and small chassis.

Some small cases can also support large motherboards. The motherboard specifications indicate which motherboards are supported.

How long is the lifespan of an assembled computer power supply?

If we talk about the life span after use, this is not necessarily true. It may break in one year, or it may not break in ten years. But if we talk about performance life, the longest is estimated to be 5 years. After 5 years, even the current mid-to-high-end configurations may even have web pages and QQ stuck by then

In fact, many computers are being operated The system was eliminated. The new operating system has high hardware requirements, and old computers are too slow to run the new operating system. Just be eliminated. This is the trend and law, and it is also the need of software and hardware manufacturers and dealers.

Assembling the computer power supply is not on?

It may be a power problem! It's very simple. Unplug everything plugged into the motherboard from the power supply first, then use a paper clip on the 20+4 pin end to connect the green wire to any black wire. If the power supply fan is spinning Then the power supply is good and can be ruled out.

After confirming that the power supply is good, connect the motherboard power supply and CPU power supply. If the independent graphics needs power supply, also connect it. However, if there is integrated graphics or nuclear graphics, it is recommended to unplug the independent graphics first (click When it lights up, it shows independently on top). Then unplug the hard drive indicator light, power indicator light, and restart button (leave only the power-on cable), and then turn on the computer. If it cannot be turned on, it means that the connection between the indicator lights, the reset button, and the power-on button is wrong. !

How to choose the power supply for assembling a computer?

1. Power, first look at the power of your power supply hardware, and look at the rated power of your graphics card and CPU.

The simplest algorithm is to add the graphics card and CPU, plus 200W. If the power is not enough, no matter how good the brand is, it will pale in comparison.

Excessive performance will feel like a waste.

2. Check the size of the chassis to see if it can fit. If it can’t fit, replace the power supply and chassis, which is a bit troublesome!

3. For wires, you can choose full modules, straight-out cables, or semi-modules. Full-module assembly is simpler.

4. Power supply efficiency and quality. Nowadays, power supplies have various solutions, such as DC-DC, EMI filters, capacitors, etc.

Solid capacitors in power supplies are better, and single-channel 12V current is better. A friend who doesn't install the computer often can't understand many parameters. Simply buy a good power supply with confidence. Look at the brand. Taiwanese and American Corsair products are not very cost-effective. In fact, they are a bit exaggerated. Domestic power supplies include Great Wall, Huntkey, Cooler, etc. to choose from.

My friends around me use Great Wall power supplies the most. Domestic power supplies from Great Wall are used in civilian, military, aerospace, supercomputers, servers, etc., which shows that they are of excellent quality. A 400W bronze power supply for home and office use is enough. Games, etc. require more than 500W, and both bronze and gold medals are acceptable. The efficiency and quality of gold medals will be better than bronze medals.

How to choose the power supply for assembling a computer?

The power supply for assembling the computer should choose a national standard brand product with a power that is at least 1/3 greater. If the power consumption of the host is 350 watts, then a nominal power supply of 450 watts or more should be used

Assemble the computer. After assembling the computer, there is no response when pressing the power button?

First of all, we need to confirm what kind of unresponsiveness this is.

1. The power fan does not spin when the computer is turned on.

Solution

Check the power cord Is there any problem? Have you connected the power strip? Is it firmly plugged in?

Check whether the cpu motherboard power supply interface is plugged in correctly! Even though it's facing the wrong way, it won't turn on even though it's plugged in.

Check whether the power supply is normal. Use a wire to plug in the green and black wires of the motherboard's power supply cable. If the fan rotates, it proves it's normal.

2. When the power supply fan is turned on, the screen does not display.

Troubleshooting: When the computer is turned on normally, the screen does not display. Press the key on the 7 keypad a few more times. If the light on the keypad turns off and on, it means the computer is running normally. It's just that the screen doesn't display. Now check to see if the display output line is connected to the graphics card normally! Graphics card graphics card! superior!

The keypad light on the top does not go out when pressed. It is usually because the memory module is not inserted securely. Re-insert it repeatedly. If it still doesn't work, there is something wrong with the motherboard or CPU.

Assemble the computer. After the assembly is completed, there is no response when pressing the power button?

Solution:

1. Plug in the power cord tightly, check the plug on the plug board, and confirm that the plug board is powered on.

2. Confirm that the wire from the host power supply to the plug-in board is good, then take the power supply and connect it to the 24P plug of the motherboard. Short-circuit the green and any black wires. If the power fan turns on, it means there is no problem with the power supply and the power fan does not work. It means the power supply is broken, replace it with a new one.

3. After confirming that there is no problem in the above 2 steps, unplug the switch wire connecting the motherboard and the front panel of the chassis, and use a screwdriver to short-circuit the two pins of the switch. If the fan rotates, it means there is no problem with the motherboard. If the fan does not rotate, it means there is no problem with the motherboard. Most likely it is a motherboard problem, please contact professional maintenance personnel to handle it.

4. Short-circuit the motherboard pins and the fan will rotate, but there is no response when pressing the switch button on the front panel. This means that the switch button is broken or stuck. Replace with a new switch button, or remove the stuck button.

How to connect the power cord of the assembled computer?

When assembling the computer power cord, you need to connect the power cord to the power supply and the computer host. The following are general steps:

1. Disconnect the power supply: Make sure the power supply and computer host are powered off, and unplug the power plug.

2. Connect the power supply: Insert the plug of the power cord into the corresponding socket of the power supply. The socket on the power supply is usually located on the back of the power supply and has a specially shaped slot to ensure that the plug is connected correctly.

3. Connect to the host: Look for the power interface on the back of the computer host, usually located on the top or bottom of the host. Plug the other end of the power cord into the power socket of the computer host.

4. Fix cables: Use cable ties or wire bundles to fix the power cord around the host to ensure that the cables are neat and safe.

5. Check the connection: Make sure the power cord is tightly connected to the power supply and computer host socket without looseness.

6. Repower the computer: Insert the power plug into the power socket and turn on the power switch to power the computer.

When connecting the power cord, please make sure to choose a power supply that meets the hardware requirements of your computer, and ensure that the power cord is installed and assembled properly to ensure that the connection is firm and safe. If you encounter any problems during connection, it is recommended to refer to the manual of the power supply or computer host, or seek professional help. Also, be careful when assembling the power cord and make sure to follow relevant safety operating procedures to protect your own safety.

How to plug in the power cord when assembling a computer?

1. Take out the motherboard, remove the CPU and install it, fix the fan, plug in the memory and put it away.

2. Remove the covers on both sides of the chassis, install the power supply, and screw the motherboard tray screws in the chassis to the designated position.

3. Handle the motherboard baffle according to the interface position, snap it into the chassis back bezel, put the motherboard correctly into the chassis, and gently tighten the screws. For independent graphics, break off the small PCI-E baffle, insert the graphics card and secure it with screws.

4. Plug in the 24+4-pin power cord. If the 4-pin cord is too long, tie it into a knot.

5. Separate the front USB and audio jack cables with USB and AUDIO letters on the back from the chassis, and insert them into the USB pin slot and AUDIO pin slot of the motherboard respectively. Both are to prevent mis-insertion. The USB pin slot is usually in the lower right corner of the motherboard, and there is a USB mark under the pin slot. The AUDIO pin slot is generally located in the middle and lower left side of the motherboard.

6. Knot the switch, restart, hard disk indicator light and other wires on the chassis. Generally, this type of plug on the motherboard is adjacent to the USB. In the lower right corner of the motherboard, there are letters indicating the corresponding plugs, such as HDLED. is the hard disk indicator light, RST is the cold start, POW-SW is the startup, SPEAKER is the alarm horn, and POW-LED is the power indicator light. Just plug them in one by one.

7. Remove the baffle at the optical drive position of the chassis (the card head can be pushed out from the back and removed). Put the optical drive in and secure it with screws.

8. Take out the optical drive and hard disk data cable. If it is a parallel port data cable, please confirm that there is an IDE interface on the motherboard. The serial port cable is generally longer. After forming a spiral shape with your fingers, you can insert it into the motherboard serial port port in sequence, and then plug in the optical drive and hard disk power cables.

9. Use tying thread to gather and fix the messy threads appropriately. Install the side covers in sequence. You're done, the next step is to partition the hard drive and create a system.

Purely personal experience, let’s discuss the shortcomings together. Reproduction is prohibited.

tb250-bct assembly computer power supply?

If you want to assemble a computer power supply, first find the power supply motherboard and connecting cables and install them, then install them on the casing of the power supply and fix them with the fixing screws before use

The above is the detailed content of Is it common to assemble computer cases? How long is the lifespan of an assembled computer power supply?. For more information, please follow other related articles on the PHP Chinese website!