電腦啟動後黑屏，只有滑鼠怎麼辦？

電腦啟動後黑屏，滑鼠正常，讓人感到手足無措。 php小編香蕉深刻理解這種困擾，特地為大家帶來這篇文章。文章將詳細介紹導致電腦黑屏的常見原因，並提供相應的解決方法。無論是硬體問題或軟體故障，我們都將逐一為您解析，助您輕鬆解決電腦黑屏難題。

一、電腦啟動後黑屏，只有滑鼠怎麼辦？

我之前電腦出現過這種情況，記得是用下面的方法就好了

二、停電後，電腦啟動後黑屏？

尊敬的用戶您好：進入系統能看到滑鼠，說明此時系統並非真的黑屏，只是顯示黑色而已，滑鼠指標顯示是正常的，表示顯示器與電腦主機均無異常，是作業系統故障了，可以用以下方法解決：

1）嘗試在系統下按「ctrl+alt+del」調出任務管理器，若能調出，將explorer進程強制結束，再在任務管理器左上角的文件選單處單擊，選擇“新工作”重新輸入“explorer.exe”重建explorer進程2）開機後嘗試進入安全模式，將顯示卡驅動卸載後重新啟動或選擇最後一次正確配置來進入系統3）如果以上方法都無效，使用者只能重新安裝系統了

三、電腦啟動後黑屏的原因及解決方法

電腦啟動後出現黑屏是一個常見的問題,可能是由多種原因導致的。作為一位專業的網站編輯,我將為您詳細分析電腦黑屏的可能原因,並提供相應的解決方法,幫助您盡快恢復電腦正常使用。

常見的電腦黑屏原因

硬體故障是導致電腦黑屏的主要原因之一。例如,顯示卡故障、主機板問題、電源故障等都可能造成電腦無法正常啟動並出現黑畫面。此外,軟體問題也可能導致黑屏,例如係統驅動程式衝突、系統崩潰等。

除此之外,BIOS設定不當也可能引發黑屏問題。例如BIOS中的顯示卡設定錯誤、啟動順序設定不當等都可能導致電腦無法正常啟動。

另外,外圍設備故障也可能引發黑屏,例如顯示器故障、連接線纜問題等。

電腦黑屏的解決方法

針對不同的原因,我們可以採取以下幾種解決方法:

檢查硬體連接是否正常,包括顯示器、主機等設備的連接線是否接好。進入BIOS檢查顯示卡設定是否正確,如果有問題可以嘗試恢復預設設定。嘗試更換顯示器或顯示卡,排查硬體故障。進入安全模式,檢查系統驅動程式是否有衝突或損壞,必要時可以嘗試系統還原。如果以上方法都無法解決,可能需要重新安裝作業系統。

總之,電腦黑屏問題可能有多種原因,需要根據具體情況進行針對性的排查和解決。希望透過這篇文章,您能夠快速定位問題所在,並採取有效的措施來解決電腦黑屏的困擾。感謝您的閱讀,祝您電腦使用愉快!

四、電腦啟動後黑屏：如何解決這一常見故障

電腦啟動後黑屏原因分析

許多人在使用電腦時都會遇到這樣的問題：電腦開機後出現黑屏，無法正常進入系統。這可能是因為硬體故障、軟體問題、驅動程式錯誤、或系統設定不當等原因造成的。

硬體故障檢查

首先，我們要檢查硬體是否發生了故障。這包括檢查主機板、記憶體、顯示卡、CPU等硬體設備是否連接良好，是否有損壞。也可以嘗試斷開不必要的外部設備，如USB設備、外接顯示器等，看看是否能解決問題。

軟體排查與修復

其次，我們可以嘗試進入安全模式，查看是否可以進入系統。如果可以進入系統，那麼可能是某些軟體或驅動程式導致了問題。此時可以嘗試卸載最近安裝的軟體，更新顯示卡驅動程序，或進行系統復原等操作來修復問題。

系統設定調整

另外，有些電腦黑屏問題可能是因為系統設定的原因造成的。我們可以嘗試重置BIOS設置，檢查顯示器連接是否正常，或調整顯示器解析度和刷新率等參數，看看是否能解決問題。

專業維修建議

如果以上方法都無法解決問題，可能需要尋求專業的維修人員協助。他們可以透過更多的專業設備和經驗來排除故障，並進行更深度的維修。

總之，電腦啟動後黑屏是一個比較常見的問題，但大多數情況下都可以透過一些簡單的操作來解決。希望本文的建議能幫助您解決這個煩惱。感謝您閱讀本文。

五、電腦啟動後黑屏，使用還原模式也是黑屏？

系統問題

　If there is a problem with your computer system, such as the installed patch is incompatible, or the software is incompatible, or the driver is incompatible, or the system itself is missing some files, it will cause a black screen.

　If it is a system failure, there are two ways to solve it. The first method is to shut down the computer and then restart it. At the same time, press and hold the F8 key on your keyboard to enter the advanced startup options.

　After entering the advanced startup options, select Perform Last Known Good Configuration from your advanced startup options. Then press Enter. After the execution is completed, you can enter the system.

　Monitor problem

First, check whether the black screen when the computer is turned on is caused by the monitor's refresh frequency being set too high. After entering safe mode, right-click the desktop and select "Properties", and select the "Settings" tab in the window that opens. Click the "Advanced" button, select the "Monitor" tab, and set the "Screen Refresh Rate" lower.

　If the problem still cannot be solved, consider whether there is a problem with the graphics card driver. Uninstall the graphics card driver in safe mode and reinstall it. In addition, the system may be infected with viruses, which may also cause this phenomenon. It is recommended to clean the system in safe mode.

6. After starting the computer, the screen goes black with only one cursor?

Methods/Steps:

1

/5

The hard disk may not be set as the startup disk, causing the system to fail to load. First, we need to enter the bios interface. Press F10 and a dialog box will pop up. Select "Y" to save the current settings.

2 The connection cable between the computer hard disk and the host is loose. We can plug it in with the boot disk first and see if we can enter the pe tool. If we cannot enter the pe tool, it means there is something wrong with the motherboard. Check if there are any obvious signs of damage on the motherboard.

3 There is a problem with system booting

Insert the boot disk into the computer, select to boot from the USB flash drive, and after entering the USB flash drive, select a PE to enter.

4 After entering, find the tool windows startup boot repair in pe, click it, select C drive after entering, and click automatic repair.

5 prompts that the repair is successful, the system boot has been successfully repaired, and you can restart the computer to enter the system.

7. What should I do if the screen goes black after the computer starts and I cannot enter the system?

1. There are many reasons for the black screen on the computer, but generally speaking, it is a failure of hardware and software. Let’s analyze the hardware failure first. For hardware, first check whether the hardware interface wiring inside the computer host is loose, and re-plug and unplug it, such as the graphics card interface.

2. Check whether the motherboard is burned. Generally, if the capacitors on the motherboard are hot and a little black and scorched, it may be that the motherboard is burned. It is recommended to take it to a professional repairman for inspection. Under normal circumstances, the fan will not turn on if the motherboard is burned out. Check it yourself.

3. Of course, it is not ruled out that the computer power supply is burned out or the computer current is unstable. Users can use the power supply to test whether the power supply is burned out.

8. After the computer starts, the screen goes black and the startup sound can be heard. what to do?

If you can hear the startup sound, it means there is no problem with the system. So use the following methods to troubleshoot the cause and see what color the monitor power light is (take the Dell monitor as an example): The light is not on - the power supply cord is not energized. Check to see if the socket plug is loose, or the plug to the monitor is loose. . Plug it in again and see if it still doesn't light up. Maybe the power cord is broken. If it still doesn't light up after changing a good wire, then the monitor is broken and you need to either repair it or buy it. If the yellow light is on - it means there is no digital signal, re-plug the serial port cable between the host and the monitor to see if it still doesn't work, the serial port cable may be broken; if the green light is on - it means the digital signal is normal, but the screen is still black. There are two reasons for this:

1. The system setting resolution is too high and the display does not support it and the screen is black (but this black screen display will pop up a prompt). The solution is to restart in safe mode and lower the resolution and then restart the system to increase it;

2. The system was pirated and the anti-piracy patch was accidentally downloaded and turned into a black screen at startup. Solution: Do not download patches after reinstalling the system.

9. Why is there a black screen with only mouse arrows after the Lenovo computer is started?

Method 1: Restart explorer.exe

1. At this time, the computer black screen has entered the system desktop, but it is not displayed. Use the keyboard to press Ctrl+Alt+Del. In the interface that appears, select "Start Task Manager".

2. In the Task Manager interface that appears, click the "File" option and click "Run New Task" that appears.

3. When the run window appears, enter "explorer.exe" and press Enter to confirm. Then the computer returned to normal.

Method 2. Reinstall the system

Many times method 1 cannot completely solve the black screen problem. The screen is still black when you open it for the second time. What should you do? Refer to the following operations to reinstall the system.

01 Prepare a USB flash drive of 4g or above. Before using the USB flash drive, you need to clear or transfer all the files in the USB flash drive.

02 Insert the prepared USB disk into another computer and open the Cloud Knight Installation Master. After opening, Cloud Knight will automatically configure the user's computer information and select the startup USB disk interface.

03 Then you enter the system selection interface. Here you can see options for various versions of windows xp windows7 windows8 windows10. Here we take windows10 as an example. There are various versions of the system for the user to choose from. Select installation here. Home version 64-bit system, then click to start production.

04 To create a USB bootable disk, you need to clear all the files in the selected USB disk. If there is any data, please back up the files yourself before starting the creation. After the backup is completed, return to the production screen and click OK.

05 Next, Cloud Knight will start downloading the system. At the same time, if you want to change the system to download, you can click Cancel Production to cancel the replacement. The system file downloaded here is large, please be patient.

06 After the production is completed, you can click to preview and simulate the U disk boot interface. Make a note of the U disk startup shortcut keys prompted by the Cloud Knight interface.

07 Insert the prepared USB disk into the faulty computer, restart the computer, and press the startup hotkey just recorded. Enter the U disk boot. If there is a Please select boot device selection interface, select the UEFI USB boot option. Enter the system boot options interface and select Windows 10 PE to enter the system.

08 After entering the system, the Cloud Knight software opens the search system image, finds the image, and clicks to install. No changes are required in the preparation for installation interface. Click Start Installation and select Continue. Waiting for installation.

09 After the installation is completed, remove the USB flash drive and click Restart Now.

10 No further operations are required, just wait patiently for the system to be installed. After the installation is completed, enter the system to complete the reinstallation.

10. After starting the computer, the screen goes black and the computer host makes beeping noises?

The computer cannot be turned on and the screen is black and there is a beeping sound. This is usually due to the board card:

1. The board card has poor contact. Pull out the memory module and independent graphics card, wipe the golden finger with an eraser to remove the oxide layer, and then re-insert it firmly.

2. The board is damaged. In other words, the memory module or graphics card is damaged and needs to be purchased new.

3. The slot is damaged. Take the memory stick as an example. Pull out the memory stick and insert it into another slot. If it can boot normally, then the memory slot of the motherboard is damaged.

4. CPU fan failure. If the CPU fan accumulates too much dust, please clear the fan dust; if the CPU fan does not rotate, please replace it.

5. The CPU or CPU fan is not installed correctly. Remove the CPU and CPU fan and re-insert them correctly, especially making sure that the CPU pins are installed correctly.

6. If none of the above reasons are the case, it may be the motherboard. If you know how to install the host yourself, you can remove the motherboard and install it on another computer to test whether it can run normally; if you don't know how to install the host, go directly to a computer repair shop for testing.

以上是電腦啟動後黑屏，只有滑鼠怎麼辦？的詳細內容。更多資訊請關注PHP中文網其他相關文章！