Bagaimana untuk menyemak sama ada kad rangkaian adalah normal di Linux

Cara menyemak sama ada kad rangkaian adalah normal di Linux: 1. Semak status kad rangkaian melalui arahan "mii-tool" 2. Semak status rangkaian melalui "status rangkaian"; status linux melalui arahan "ifconfig -a" Maklumat tentang semua antara muka rangkaian 4. Tanya maklumat kad rangkaian melalui arahan "ethtool".

Persekitaran pengendalian tutorial ini: sistem linux5.9.8, komputer Dell G3.

Bagaimana untuk menyemak sama ada kad rangkaian adalah normal di Linux?

Semak status kad rangkaian atau sambungan di bawah Linux

1) Gunakan arahan mii-tool

       [root@localhost root]# mii-tool
        eth0: negotiated 100baseTx-FD, link ok
        eth1: no link

atau

      [root@localhost root]# mii-tool -v
        eth0: negotiated 100baseTx-FD, link ok
          product info: vendor 00:50:43, model 2 rev 3
          basic mode:   autonegotiation enabled
          basic status: autonegotiation complete, link ok
          capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
          advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
          link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
        eth1: no link
          product info: vendor 00:50:43, model 2 rev 3
          basic mode:   autonegotiation enabled
          basic status: no link
          capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
          advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control

atau

      [root@localhost root]# mii-tool -w
       21:20:33 eth0: negotiated 100baseTx-FD, link ok
       21:20:33 eth1: no link
      //mii-tool主要是用于配置网卡工作模式的指令，同时也可以进行查询、监控等工作！

2)

     [root@localhost /]# /etc/init.d/network status
      Configured devices:
      lo eth0 eth1
      Currently active devices:
      lo eth0

Bersamaan dengan

     [root@localhost root]# service --status-all
      ............
      ............
      Configured devices:
      lo eth0 eth1
      Currently active devices:
      lo eth0
      ............
      ............

3)ifconfig -a

    [root@localhost /]# ifconfig -a
    eth0 Link encap:Ethernet HWaddr 00:09:6B:09:08:FC
          inet addr:192.168.10.1 Bcast:192.168.10.255 Mask:255.255.255.0
          inet6 addr: fe80::209:6bff:fe09:8fc/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:106732953 errors:0 dropped:0 overruns:0 frame:0
          TX packets:104379788 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:2351331877 (2.1 GiB) TX bytes:391707945 (373.5 MiB)
          Base address:0x2500 Memory:fbfe0000-fc000000
   eth1   Link encap:Ethernet HWaddr 00:09:6B:09:08:FD
          BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
          Base address:0x2540 Memory:fbfc0000-fbfe0000

4)ethtool

#ethtool eth0
Settings for eth0:
        Supported ports: [ MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes: 10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: d
        Current message level: 0x000000ff (255)
        Link detected: yes

#ethtool eth1

Settings for eth1:
        Supported ports: [ MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes: 10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
        Advertised auto-negotiation: Yes
        Speed: Unknown! (0)
        Duplex: Half
        Port: Twisted Pair
        PHYAD: 1
        Transceiver: internal
        Auto-negotiation: on
        Supports Wake-on: g
        Wake-on: d
        Current message level: 0x000000ff (255)
        Link detected: no

Seperti yang anda lihat daripada di atas, eth0 disambungkan dan eth1 tidak disambungkan

Cadangan berkaitan: "Tutorial Video Linux"

Atas ialah kandungan terperinci Bagaimana untuk menyemak sama ada kad rangkaian adalah normal di Linux. Untuk maklumat lanjut, sila ikut artikel berkaitan lain di laman web China PHP!