CISCO路由器连接ADSL之PPPoE配置

CISCO 路由器 连接 ADSL之PPPoE 配置 Cisco 路由器 连接 ADSL modem的PPPoE 配置 ： hostname bjsite ! ip subnet-zero no ip domain-lookup ! vpdn enable no vpdn logging ! vpdn-group 1 request-dialin protocol pppoe ! interface Ethernet0/0 ip addre

CISCO路由器连接ADSL之PPPoE配置

 

Cisco路由器连接ADSL modem的PPPoE配置：

 

hostname bjsite 

! 

ip subnet-zero 

no ip domain-lookup 

! 

vpdn enable 

no vpdn logging 

! 

vpdn-group 1 

request-dialin 

protocol pppoe 

! 

interface Ethernet0/0 

ip address 192.168.0.1 255.255.255.0 

ip nat inside 

no ip mroute-cache 

! 

! 

! 

! 

interface Ethernet0/1 

no ip address 

pppoe enable 

pppoe-client dial-pool-number 1 

!   www.2cto.com  

interface Dialer1 

ip address negotiated 

ip nat outside 

ip mtu 1492 

encapsulation ppp 

no ip mroute-cache 

dialer pool 1 

dialer-group 1 

ppp authentication pap 

ppp pap sent-username dg48907653@163.gd password xxxxxxxx

! 

ip classless 

no ip http server 

! 

dialer-list 1 protocol ip permit 

ip nat inside source list 1 interface Dialer1 overload

ip route 0.0.0.0 0.0.0.0 dialer1 

access-list 1 permit 192.168.0.0 0.0.0.255 

! 

line con 0 

exec-timeout 0 0 

transport input none 

line vty 0 4 

login 

! 

end

 

Cisco路由器连接ADSL WIC卡之PPPoE配置：

 

vpdn-group pppoe 

request-dialin 

 

!--- we are the PPPoE client requesting to establish 

!--- a session with the aggregation unit (6400 NRP). 

 

protocol pppoe 

! 

  www.2cto.com  

!--- internal Ethernet network.

 

! 

interface FastEthernet0 

ip address 10.92.1.182 255.255.255.0 

ip nat inside 

 

!--- DSL interface.

! 

interface ATM0 

no ip address 

no atm ilmi-keepalive

bundle-enable

dsl operating-mode auto

hold-queue 224 in

 

!--- All defaults.

 

!--- PPPoE runs on top of AAL5SNAP, but the 

!--- encap aal5snap command is not used. 

 

! 

interface ATM0.1 point-to-point 

pvc 1/1 

pppoe-client dial-pool-number 1

 

!--- pvc 1/1 is an example value that must be changed 

!--- to match the value used by the ISP. 

  www.2cto.com  

! 

 

!--- The PPPoE client code ties into a dialer interface upon 

!--- which a virtual-access interface is cloned. 

! 

interface Dialer1 

ip address negotiated 

ip mtu 1492

 

!--- Ethernet MTU default = 1500 (1492 + PPPoE headers = 1500)

 

ip nat outside 

encapsulation ppp 

dialer pool 1

 

!--- Ties to atm interface. 

 

ppp authentication chap callin 

ppp chap hostname  

ppp chap password

! 

!--- The ISP will instruct you regarding 

!--- the type of authentication to use. 

!--- To change from PPP CHAP to PPP PAP, 

!--- replace the following three lines:

!--- ppp authentication chap callin 

!--- ppp chap hostname  

!--- ppp chap password  

!--- with the following two lines:

!--- ppp authentication pap callin

!--- ppp pap sent-username password

  www.2cto.com  

!--- For NAT we are going to overload on the Dialer1 

!--- interface and add a default route out 

!--- since dialer ip address can change. 

 

ip nat inside source list 1 interface Dialer1 overload 

ip classless 

ip route 0.0.0.0 0.0.0.0 dialer1 

no ip http server 

! 

access-list 1 permit 10.92.1.0 0.0.0.255