Gigabyte motherboard won't turn on

What should I do if my computer with a Gigabyte motherboard cannot be turned on? The 4 lights are always on

. First unplug the computer power cord and press the power button 5- on the chassis. 6 times. Release the residual charge on the motherboard. 2. Then open the side panel of the chassis and insert and pull out the memory slots. 3. Remove the CMOS battery from the motherboard and reinstall it after 1 minute. If your computer has a separate graphics card, it is best to plug and unplug the graphics card.

Check whether the computer components are inserted securely. First, check whether the monitor cable is securely and reliably inserted into the host interface, and then check whether the contact between the graphics card and the motherboard IO slot is good. If necessary, please remove the graphics card and reinsert it once, making sure it is inserted in place and has good contact.

Check to see if there is any problem with the voltage in your home. Open the case and look carefully at the motherboard to see if there are any obvious signs of damage, especially those capacitors. It is recommended that you use the minimal system method, which is to exclude non-essential hardware for the computer to work and only allow the necessary hardware to work.

Check whether the computer components are inserted securely. First, please check whether the monitor cable is securely and reliably inserted into the host interface, and then check whether the contact between the graphics card and the motherboard IO slot is good. If necessary, please remove the graphics card and reinsert it once, making sure it is inserted in place and has good contact.

The inability to boot should have nothing to do with PHASELED. Try to pull out the memory stick, wipe off the gold finger with an eraser and then plug it back in; if you have a graphics card, if you still can't turn on the computer after cleaning the memory, clean the graphics card just like you did to clean the memory; also make sure the monitor connector is plugged in securely. If it still doesn't work, you can only reinstall the system.

The computer cannot be turned on when gigabyte occurs

1. The first is a hard disk failure. The motherboard cannot recognize the startup disk and actively exits the BIOS. You can check here to see if the BIOS can still recognize yours. If the startup disk is recognized, you can also try to repair the startup program and boot area. If it is not recognized, you may need to replace the hard disk.

2. If you don’t know where the specific problem is and there is no alarm sound, then consider the simplest problem first. For example, if the memory stick is loose, or the motherboard cannot recognize the memory due to oxidation of the gold finger, then unplug the memory stick, wipe it clean, insert it and start the computer. This will usually solve the problem.

3. Check whether the computer components are inserted securely. First, check whether the monitor cable is firmly and reliably inserted into the host interface, and then check whether the contact between the graphics card and the motherboard IO slot is good. If necessary, please remove the graphics card and reinsert it once, making sure it is inserted in place and has good contact.

4. Generally, there are two reasons leading to this phenomenon. The first is a hard disk failure. The motherboard cannot recognize the startup disk and actively exits the BIOS. You can check here to see if the BIOS can still recognize your startup disk. If it can be recognized, you can also try to repair the startup program and boot area. If it cannot be recognized, it may be a problem. It's time to replace the hard drive.

5. When turning on the Gigabyte motherboard, NO bootable device is detected appears, indicating that the bootable device is not set. The solution is as follows: Press the Del key when turning on the motherboard. The computer enters the BIOS page and selects the second option. Click to enter to find the startup device option and click to enter.

What to do if Gigabyte cannot turn on

1. Possible reasons: The IDE cable is of poor quality or not plugged in firmly. Solution: Change an IDE cable or plug the IDE cable into another IDE slot on the motherboard. Do not connect the hard disk cable with other IDE devices, such as optical drives. Separate the two IDE cables and set the master and slave disks correctly.

2. If the memory and graphics card cannot be solved after wiping it, you can remove the COMS battery from the motherboard, cut off the power, and install it after a few minutes. Sometimes due to hardware changes, the coms configuration changes may cause the computer to fail to boot.

3. Cut off the power, open the case, clean the dust, especially the dust on the CPU fan, and check whether the CPU fan rotates normally. Insert and remove the memory, wipe the golden finger part with an eraser, and re-insert it tightly (do not reverse it). Insert and remove the graphics card, wipe the golden finger part with an eraser, and re-insert it tightly (the buckle must be buckled).

4. When turning on the Gigabyte motherboard, NO bootable device is detected appears, indicating that the bootable device is not set. The solution is as follows: Press the Del key when turning on the motherboard. The computer enters the BIOS page and selects the second option. Click to enter to find the startup device option and click to enter.

5. When the computer unexpectedly starts up and directly enters the gigabyteBios page, we can first check whether the hard disk startup item is correct in Bios. By default, sometimes it will happen due to unexpected power outage or unexpected shutdown and other special circumstances. This causes errors in the Bios configuration and causes problems with the startup items. The hard drive is not detected in the bios interface.

The computer always stops at the gigabyte interface

1. Generally, there are two reasons for this phenomenon. The first is a hard disk failure. The motherboard cannot recognize the startup disk and actively exits the BIOS. You can check here to see if the BIOS can still recognize your startup disk. If it can be recognized, you can also try to repair the startup program and boot area. If it cannot be recognized, it may be a problem. It's time to replace the hard drive.

2. The first is a hard disk failure. The motherboard cannot recognize the startup disk and actively exits the BIOS. You can check here to see if the BIOS can still recognize your startup disk. If it can, you can also try to repair the startup program. and boot area, if it cannot be recognized, the hard disk may need to be replaced.

3. When the computer unexpectedly boots up and directly enters the gigabyteBios page, we can first check whether the hard disk startup item is correct in Bios. By default, sometimes the Bios configuration is caused by special circumstances such as unexpected power outage or unexpected shutdown. An error occurred, causing a problem with the startup item. The hard drive is not detected in the bios interface.

4. In addition, it may be caused by hardware problems, such as memory, hard disk, etc. failure. You can try to disassemble the relevant hardware for inspection, or contact after-sales service. If none of the above methods solve the problem, you may consider contacting GIGABYTE motherboard customer service and providing specific error information so they can help diagnose the problem.

5. The hard disk is not detected in the bios interface. Most likely the hard drive is broken.

The above is the detailed content of Gigabyte motherboard won't turn on. For more information, please follow other related articles on the PHP Chinese website!