The computer cannot boot after adding a memory stick

After replacing the memory module, the computer cannot be turned on!

First, there is a problem with the plug, second, the memory is incompatible, third, the memory connection is not OK, bad contact.

The memory module is not installed properly: Check whether the memory module is firmly inserted into the slot. If it is not installed properly, the computer will not start. It is recommended to disassemble and install again. Incompatible memory module: The specifications of the memory module do not meet the requirements of the computer, such as capacity, frequency, etc., which may cause the computer to fail to boot.

If there is a dust problem, remove the dust first, especially in memory slots that have been empty for a long time. There may be dust, causing poor contact of the memory modules. Compatibility issues. If the old article can work normally, it means there is no problem.

So the computer cannot be started. If the computer cannot be turned on after adding new memory, the possible problems include the following: the memory module interface is not clean, and the dust on the interface needs to be wiped off before reinserting it. The memory module is not inserted in place and the buckles on both sides are not fastened firmly. The memory module specifications are incorrect, and the main frequency exceeds the motherboard requirements. The memory module is broken.

The computer has a black screen after a new memory module is turned on

The monitor is damaged: Repair or replace the monitor. The memory module is incompatible with the motherboard: Replace it with a memory module with the same specifications as the one used before. The memory module was not installed successfully: Install the memory module correctly in the card slot.

First of all, it may be that the model of the memory slot in the computer host does not match the model of the memory, resulting in a black screen at startup. After installation, it is also possible that the memory module added later is incompatible with the motherboard, which will also cause such problems.

Poor contact of the memory module will cause the computer to fail to boot normally. Disassemble and reinstall. The specific operations are as follows: First, determine whether the model of the memory slot in the computer host matches the model of the memory. If you don’t know the model number, just look at the location of the slots and memory gaps.

Your situation may be caused by the fact that you did not insert the new memory stick tightly when you inserted it. When you inserted the memory stick into the slot at an angle, press it in hard, and then press it down again and it will get stuck. . You should have no compression issues.

You can use an eraser to wipe the golden finger of the memory stick to remove the oxygen layer of the memory stick, and then insert the memory stick into the memory slot. Maybe the memory sticks are not of the same brand or are of different generations or frequencies and are not compatible, causing a black screen at startup.

It doesn’t seem to be due to the slot. Later, the maintenance engineer reminded me to try powering down the motherboard. So, I removed the CMOS battery from the motherboard, waited a while, and reinstalled it. When I turned on the computer, it started smoothly and the fault was eliminated.

The computer cannot be turned on after adding a memory stick. What's going on?

1. This situation may occur due to the following reasons: the memory stick is not installed properly: check whether the memory stick is firm. The ground is inserted into the slot. If it is not installed properly, the computer will not start. It is recommended to disassemble and install again.

2. The reason is that the new memory module installed does not meet the computer requirements and cannot be started normally, so the computer cannot be turned on. If the computer cannot be turned on after adding new memory, the possible problems include the following: the memory module interface is not clean, and the dust on the interface needs to be wiped off before reinserting it. The memory module is not inserted in place and the buckles on both sides are not fastened firmly.

3. The memory module is loose, aging or has quality problems, which will lead to no display failure after powering on. The specific reason cannot be determined by the machine without seeing it. Other common reasons: the memory is loose or there is a problem with the memory itself. Re-insert the memory or try another memory.

4. Poor contact of the memory module will cause the computer to fail to boot normally. Disassemble and reinstall. The specific operations are as follows: First, determine whether the model of the memory slot in the computer host matches the model of the memory. If you don’t know the model number, just look at the location of the slots and memory gaps.

What to do if the computer cannot boot after inserting memory

Some motherboards are like this. If too many memory modules are inserted, problems will occur, causing the computer to fail to start and other problems. If this is the case, you can consider going to a merchant to replace the motherboard. In addition, in view of the situation at the beginning of the article, Master Lu recommends that you take your computer to the merchant for a physical examination.

You can remove the COMS battery from the motherboard, cut off the power, wait a few minutes and then install it. Sometimes the COMS configuration changes due to hardware changes, which may also cause the computer to fail to boot. If none of these work, consider it. Motherboard or cpu problem.

If there is a dust problem, remove the dust first, especially in memory slots that have been empty for a long time. There may be dust, causing poor contact of the memory modules. Compatibility issues. If the old article can work normally, it means there is no problem.

If the computer cannot be turned on after replacing the memory, it means that the memory module may be incompatible with the computer. Contact the memory dealer to determine whether the memory of the same model cannot be turned on after replacing the memory. The main reasons are as follows: 1. The original memory is useless, and all the new memory is used. , it cannot be turned on, it is probably an incompatibility problem, that is, the computer is old and the memory module is new, and the computer does not recognize it.

The computer can be turned on by inserting one memory stick, but cannot be turned on by inserting two. Since the motherboard has two memory slots, it must be reasonable and can be used normally. As you said: two memories and two slots can be used independently, but they cannot be used at the same time. This situation usually occurs due to power supply problems.

Still double-sided. If you go to 1066, you may not recognize it. If two laptop memory modules are used together, they will automatically form dual channels. But if the two speeds are too mismatched, compatibility problems will occur, resulting in the inability to boot. It is also possible that the memory slot may have poor contact if left idle for a long time. Just plug one in and judge.

The computer cannot boot after the memory stick is plugged in

The details are as follows. If only one memory stick can boot, the other memory stick is bad. If two pieces of memory can be turned on individually but cannot be turned on together, it means there is a serious compatibility problem. If neither memory can boot, it may be that the memory is bad or the computer is broken. Can be determined by substitution method.

If the troubleshooting method shows that the memory is all good, then it is likely that there is a memory compatibility issue or a problem with the motherboard memory slot that prevents the computer from starting. Some motherboards are like this. If you plug in too many memory modules, problems will occur, resulting in problems such as the computer not being able to start. If this is the case, you can consider going to a merchant to replace the motherboard.

Poor contact of the memory module will cause the computer to fail to boot normally. Disassemble and reinstall. The specific operations are as follows: First, determine whether the model of the memory slot in the computer host matches the model of the memory. If you don’t know the model number, just look at the location of the slots and memory gaps.

If the computer cannot be turned on after replacing the memory, it means that the memory module may be incompatible with the computer. Contact the memory dealer to determine whether the memory of the same model cannot be turned on after replacing the memory. The main reasons are as follows: 1. The original memory is useless, and all the new memory is used. , it cannot be turned on, it is probably an incompatibility problem, that is, the computer is old and the memory module is new, and the computer does not recognize it.

Confirm whether the memory module is fully inserted as shown in the figure below. Error: Correct: Confirm whether the memory pins of the motherboard or the memory slot are dirty as shown below. If so, please clear it and try again. Please confirm whether the memory module is of a specification or brand supported by the motherboard.

The above is the detailed content of The computer cannot boot after adding a memory stick. For more information, please follow other related articles on the PHP Chinese website!