How to fix laptop hard drive that cannot be read

What to do if the computer does not recognize the hard drive? How to fix the hard drive that cannot be read?

This failure is usually caused by a problem with the connection between the hard drive and the motherboard. If such a problem occurs, you can replace a connecting cable between the motherboard and the hard disk. If the fault still cannot be eliminated, you can check whether the master and slave cable settings are correct.

Solution: If such a problem occurs, you can replace a connecting cable between the motherboard and the hard disk. If the fault still cannot be eliminated, you can check whether the master-slave cable settings are correct.

Poor contact between hard disk cable or hard disk interface: First, we can check the data cable and interface part. If the hard disk data cable is broken or aged, we can try to replace it to see if the recognition can be restored. If the hard disk interface is oxidized In this case, you can also wipe it with an alcohol swab.

First turn on the computer and press the del key to enter the bios and restore the default values. See if the hard drive can be recognized in boot or if the settings are incorrect. Check whether the hard drive is plugged in properly or damaged. You can also try replacing the bios battery.

What to do if the computer hard drive cannot be read

1. When the computer cannot recognize the hard drive, we need to try some of the following solutions: Check whether the hard drive is correctly connected: First, we need to confirm whether the hard drive is correct Connect to computer, including data cable and power cable. If you find that the hard drive connection is loose or loose, you need to reconnect it.

2. The cause of this type of failure is the connection between the hard disk and the motherboard. You can replace the connection between the hard disk and the motherboard, or take a look at the master and slave connections on the hard disk. Whether the lines are set correctly, etc.

3. Poor contact between hard disk cable or hard disk interface: First we can check the data cable and interface part. If the hard disk data cable is broken or aged, we can try to replace it to see if the recognition of the hard disk interface can be restored. If the hard disk interface If oxidation occurs, you can also wipe it with an alcohol swab.

4. The computer hard disk cannot be read. Solution: The hard disk does not respond after powering on. When the power is turned on and the laptop is started, it is found that the hard disk has no response and the hard disk cannot be found in the BIOS. If this happens, it's mostly caused by a problem with the hard drive motor.

5. First use a screwdriver to open the computer case, and then re-plug the computer hard drive data cable and power cable. Open BlOS, view the standardomosfeaures page, check whether the hard disk is set to None, and set this item to auto. Then find the ATA (SATA) option and select it.

6. You can find a replacement circuit board of the same model. If it cannot be repaired and the data on the disk is really valuable, you can find a professional to recover the data in the hard disk. The motherboard bios settings are incorrect and the hard drive cannot be recognized. The hard disk parameter settings in the BIOS are incorrect, the self-test fails, and the hard disk cannot be used normally.

The laptop cannot read the hard disk

The USB is not recognized by the computer, if it is due to the system or the driver that comes with the system. Press F8 on boot to enter safe mode and then exit. Select restart or shutdown before booting to enter normal mode (repair the registry). Set CMOS parameters.

Poor contact between hard disk cable or hard disk interface: First, we can check the data cable and interface part. If the hard disk data cable is broken or aged, we can try to replace it to see if the recognition can be restored. If the hard disk interface is oxidized In this case, you can also wipe it with an alcohol swab.

The solution is as follows: Right-click this computer (computer) and click Open. Click on the left to open it, and find the mobile hard drive on the right.

Then the problem that the computer cannot detect the hard drive or cannot recognize the hard drive may lie in the connection between the hard drive and the motherboard. You can try replacing the motherboard and hard drive cables, or see if the master-slave cable settings are correct, and listen to see if there are any strange sounds while the hard drive is running.

The computer hard disk cannot be read. Solution: The hard disk does not respond after powering on. When the power is turned on and the laptop is started, it is found that the hard disk has no response and the hard disk cannot be found in the BIOS. If this happens, it's mostly caused by a problem with the hard drive motor.

Open your laptop, find the "My Computer" icon and right-click it. In the pop-up properties window, find the "Manage" option and click on it. In the Computer Management window, find the Storage submenu Disk Management option and click it.

How to fix a laptop hard drive that cannot be read

Restart the computer: Sometimes, simply restarting the computer can resolve temporary software issues. Try restarting your computer and plugging in the hard drive again to see if the problem is resolved. Replace the data cable and interface: Try to replace the data cable or connection interface of the mobile hard disk.

The solution is as follows: Right-click this computer (computer) and click Open. Click on the left to open it, and find the mobile hard drive on the right.

Solution: It may be caused by poor contact between the hard drive and the motherboard. You can check whether the connecting cable is damaged. It may also be that the gold fingers on the hard drive circuit board are oxidized and need to be cleaned. It may be caused by the "hard disk boot" being damaged, and you can reinstall the system.

The system cannot recognize the hard disk. Most of these faults occur on the connection cable or IDE port. The hard disk itself is unlikely to be faulty. You can perform replacement tests by re-plugging the hard disk cable or changing the IDE port and cable, and you will quickly find the fault. CMOS failure.

The solution is as follows: Insert the mobile hard disk into the computer, select the computer, select "This Computer" on the left, and right-click. Select "Manage" and click to enter Computer Management; select the disk "Disk Management". If you do not see the mobile hard disk, you can select More Operations on the right to rescan the disk.

The above is the detailed content of How to fix laptop hard drive that cannot be read. For more information, please follow other related articles on the PHP Chinese website!