How to set solid state drive as system disk on computer

How to make a solid state drive a system disk

1. When purchasing a solid state drive, first check the capacity and interface of the solid state drive. Nowadays, there are many types of interfaces for solid state drives, such as SATA. , PCI, etc. After we confirm the interface, install the solid-state drive on the computer's motherboard and set the solid-state drive as the primary hard drive in the BIOS.

2. Install the solid state drive into the computer. Enter the computer BIOS and place the solid-state drive in front of the original mechanical hard drive in the boot sequence. install the system. Select the installation drive (SSD). Click OK. Continue the installation.

3. regedit" to bring up the registry. Then, find HKEY_LOCAL_MACHINE\ SYSTEM\ MoutedDevices, find \DosDevices\"Solid State Drive Letter", and change the "Solid State Drive Letter" to "C", No need to add quotation marks, then restart the computer. Finally, change the C drive letter of the original mechanical hard disk to the original SSD drive letter.

4. Use DiskGenius and other software to set the system disk (SSD) as active. Set other hard drives to be inactive, as shown below. 2. Enter the BIOS and set the preferred boot disk to SSD, as shown below. 3. Open the computer from winPE and install the system, as shown below.

5. Operation Please ensure that the solid state drive has been installed in the computer and the data cable and power cable are plugged in before starting the computer. Press and hold the DEL key to enter the BIOS when the computer is turned on. After entering the BIOS, use the up and down arrows to select System Summary and press the enter key.

6. How to set a solid-state drive as a startup disk in a laptop. Before operating, please make sure that your solid-state drive has been installed in the computer and the data cable and power cord are plugged in.

I have added an SSD solid-state drive to the computer. How to set it up? SSD is used as a system disk

When purchasing a solid state drive, first check the capacity and interface of the solid state drive. Now there are many types of interfaces for solid state drives, such as SATA, PCI, etc. After we confirm the interface, install the solid state drive in The motherboard of the computer, and set the solid-state drive as the primary hard drive in the BIOS.

First remove the mechanical hard drive, and then install the system on the solid-state drive.

Please ensure that the solid-state drive is installed on the Plug in the data cable and power cable to the computer. Press and hold the DEL key to enter the BIOS when the computer is turned on. After entering the BIOS, use the up and down arrows to select System Summary and press the enter key.

How to set the solid state drive as the system Disk

When purchasing a solid-state drive, first check the capacity and interface of the solid-state drive. Now there are many types of interfaces for solid-state drives, such as SATA, PCI, etc. After we confirm the interface, install the solid-state drive on the motherboard of the computer. on the computer, and set the solid-state drive as the primary hard drive in the BIOS.

First remove the mechanical hard drive, and then install the system on the solid-state drive.

Use the U disk to boot the disk, and in winPe, copy the mechanical hard drive Hard disk C drive to solid state drive. The solid state drive needs to be partitioned in advance (divided into one area). After the copy is completed, use the boot tool in winPe to repair the solid state drive.

Please ensure that the solid state drive has been installed on the computer before operation And plug in the data cable and power cable. When the computer is turned on, press and hold the DEL key to enter the BIOS. After entering the BIOS, use the up and down arrows to select System Summary and press the enter key.

. Use DiskGenius and other software to restore the system The disk (solid-state disk) is set to active, and other hard disks are set to inactive, as shown below. 2. Enter the BIOS and set the preferred boot disk to SSD as shown below. 3． Open the computer from winPE and install the system, as shown below.

The next step is to enter the BIOS interface. Then use the left and right keys on the keyboard to move the cursor to the startup option. Use the up and down keys on your keyboard to move to the boot option and press the Enter key.

How to use a solid-state drive to make a system disk|How to use a solid-state drive to make a system disk

Copy the win10 system iso image directly to the U disk. The micro-pe boot disk supports images larger than 4G; during installation Insert a USB flash drive into a computer with an SSD solid state drive. In order to take advantage of the speed of the SSD, you must first enter the BIOS to turn on the AHCI mode of the hard drive. However, new computers default to AHCI and do not need to change it. This step can basically be omitted.

When purchasing a solid-state drive, first check the capacity and interface of the solid-state drive. Now there are many types of interfaces for solid-state drives, such as SATA, PCI, etc. After we confirm the interface, we install the solid-state drive on the motherboard of the computer. , and set the solid state drive as the primary hard drive in the BIOS.

How to install a solid-state drive to turn it into a c drive: First, install a new solid-state drive on the original computer (of course it is not a solid-state drive). This hard drive must have no data and no partitions. Install the solid-state drive to the location of the original mechanical hard drive, and install the mechanical hard drive to the location of the optical drive.

The AHCI mode must be turned on in the bios. Generally, for new computers, such as those purchased within 2 years, you basically don’t need to worry about it, because it only has AHCI mode. If you have an earlier computer, there are two types: IDE mode and AHCI mode. Before installing the system, just set it to AHCI.

Asus motherboard can set the solid state drive to start by following the following steps: When you see the startup screen, press the "del" key continuously to enter the BIOS setting interface. As shown in the figure below: At this time, when we press the "F8" key, we will enter the boot menu selection window, as shown in the figure below: Through the above steps, you can select the solid state drive to start.

How to set the solid-state drive as the main hard drive boot disk in a notebook

1. After turning on the computer, when the motherboard self-test screen or brand LOGO screen appears, press the BIOS hotkey quickly and continuously (different brands and models of computers The BIOS hotkeys are different (usually the F2 key on laptops and the DEL key on desktops) to enter the BIOS setting interface.

2. Install the solid state drive into the computer. Enter the computer BIOS and place the solid-state drive in front of the original mechanical hard drive in the boot sequence. install the system. Select the installation drive (SSD). Click OK. Continue the installation.

3. You need to choose to enter the BIOS settings when booting, select the startup option in the BIOS, and select the solid-state drive to move to the top and the first startup item. I hope this can help you. Sometimes Bai Du can't make a mistake in judgment, so don't worry about him.

How to set the solid-state drive as the primary hard drive for startup

Turn on the computer and repeatedly press the Delete key on the keyboard to enter the main interface of the motherboard BIOS. (See picture below). Use the keyboard arrow keys to select the "Advanced BIOS Features" item (translation of this item: Advanced BIOS Properties), and press the "Enter" key to enter. (See picture below).

Click the drop-down box on the right to set the solid-state drive as the startup disk. At this time, the system will boot from the solid state drive first. If the solid state drive does not have an operating system, it will boot from the second hard drive. That’s it.

The most commonly used method is to change the bios settings. Press F10 to enter the bios settings when booting. Press the → key to go to the advanced option, then the ↓ key to go to the ide configuration item, and press Enter to enter. Similarly, use the keyboard to select sata operation mode, then select compatible, and press the Enter key to enter.

You need to choose to enter the BIOS settings when booting, select the startup option in the BIOS, and select the solid-state drive to move to the top and the first startup item. I hope this can help you. Sometimes Bai Du can't make a mistake in judgment, so don't worry about him.

After booting into the bios settings, you can see the boot device Priority, which is the choice of the boot order for the hard disk and other devices. If you have two hard drives, you need to set the priority of the hard drives first. Enter the Hard Disk Drivers in the picture above and specify the order of the two hard disks.

The above is the detailed content of How to set solid state drive as system disk on computer. For more information, please follow other related articles on the PHP Chinese website!