How to configure RCA universal remote using code?

You can use the RCA universal remote to simplify remote control management. With various models, you can control up to eight devices, eliminating the need for multiple remotes and reducing clutter. Be patient in programming the remote and follow the simple steps provided. So, if you want to configure an RCA universal remote using codes, this article is for you.

How to configure the RCA universal remote using code

To configure your RCA Universal remote using code, use one of the following methods.

Programming the RCA Universal Remote Using the Automatic Programming Method

Programming RCA Universal Remotes Using Direct Codes

Let’s talk about it in detail.

1] Programming the RCA Universal Remote Using the Automatic Programming Method

We are going to start with a simple and easy method as we will be setting up the RCA universal remote using automatic programming. Follow the steps below to do the same.

Start the device to be configured.

Press and release the TV button and wait for the remote's on/off button to light up, the remote will stay lit.

You need to press and hold the TV button and the On/Off button at the same time until the On/Off dims to no brightness. It should open automatically, and after that, you can release the button we asked you to grab.

To program the RCA remote, press and release the play button. If the TV or component you are programming does not turn off after 5 seconds, press the play button every 5 seconds until it turns off. This means the remote is searching for possible codes for your TV.

The TV will turn off, which means it found the code it was looking for.

You must then press and release the reverse button and wait for the TV to turn back on. Make sure you keep tapping the button every three seconds until the TV turns back on.

You can now press and release the Stop button to allow the configuration to be saved.

It should be noted that pressing the wrong button may cause problems with the synchronization mechanism. Setting up the remote can involve a learning curve that includes some trial and error. If you need to start over, simply restart the hardware, remove the remote battery, reinsert it, and follow the steps again. Likewise, you can add multiple devices if needed.

2] Programming an RCA Universal Remote Using Direct Codes

Your RCA remote comes with a code book that allows manual entry of codes for various devices. However, not everyone carefully places their stuff, let alone codebooks. If you lose it, don't worry! Find all RCA universal remote codes from rcaachories.com/emote-code-finder. When using it, you need to find the "revision number" on the sticker under the battery. You simply go to the website linked earlier, select and enter the correct details, and search for the code. Once you have the code we need, follow the steps mentioned below to set up the remote.

In the Codebook, navigate to the TV section, go to the Manufacturer section, and write down the code.

Turn on the TV.

Then you have to pick up the remote control, press and hold the TV button and wait for the power button to light up.

Enter the first marked code while holding down the TV button.

After entering the device code, press and hold the TV button. If the power button still lights up, you entered the code correctly. Release the TV button to start testing device commands. If everything works fine, you should now be able to control your TV using power, volume, and menu commands.

Please keep in mind that if the power button flashes four times, it means that the code you entered is wrong and you need to check the next code in the code book or booklet.

Read: Set up a Kodi remote on PC using Android and iOS devices

How to reset the RCA universal remote control?

If your RCA universal remote controller malfunctions or does not work properly, you can try to reset it to solve the problem. First, remove the battery from the remote control. Next, press and hold the "1" button on the remote for a while, which will reset the remote's internal processor. After holding down the "1" button, release the button and install new batteries into the remote. This simple step may help restore normal functionality to your remote control.

Read: With Unified Remote, you can control your Windows PC with your smartphone

How do I connect my universal remote to my TV with a password?

To use a code to connect your universal remote to your TV, you must first find the code. You can easily find them if you have the code book that came with the remote, and if you lose it you can get the codes from RCA's website. Check out the previously mentioned guide to find the code and configure your remote.

Also Read: Firestick remote not working even after changing batteries.

The above is the detailed content of How to configure RCA universal remote using code?. For more information, please follow other related articles on the PHP Chinese website!