


php Editor Banana, it may be confusing for you when your motherboard does not have a fault light coming on. The fault light is usually used to indicate problems happening on the motherboard, but if it doesn't come on, then you may need to take other methods to diagnose the problem. First, make sure all power connections on the motherboard are correct. Then, check other lights on the motherboard, such as the power light and hard disk light, to see if they are working properly. Additionally, you can further troubleshoot the problem by checking BIOS settings and using diagnostic software. If you still cannot resolve the issue, it is recommended that you seek professional help to ensure that your motherboard is functioning properly.
What should I do if there is no fault light on the motherboard?
1. Turn on the power supply and check whether the power fan is rotating. If the power supply fan is not spinning, the power supply is faulty.
2. Re-plug the 20P power cord that supplies power to the motherboard from the computer. The computer won't turn on and the motherboard light doesn't turn on. Is the motherboard broken?
3. If the motherboard still does not respond after being turned on by unplugging and plugging, it means there is a problem with the motherboard.
4. If it still doesn’t work, it is recommended to go to a repair shop for repair or replacement
What is the CPUfanOPT on the motherboard? Monitoring display is 0?
1. CPU_FAN (cooling fan power socket) pin 1 (ground pin), pin 2 (12V), pin 3 (speed detection pin), pin 4 (speed control pin) 2. CPU_OPT ( Water cooling fan power socket) Pin 1 (ground pin), pin 2 (12V/speed control pin), pin 3 (speed detection pin), pin 4 (VCC) If an air-cooled radiator is used, plug the radiator into At CPU_OPT, you will find that the COU optional fan display speed in the motherboard BIOS will change when adjusting the CPU_FAN speed, and there is no option to turn it off.
The main performance of the fan is reflected in the following aspects: rotation speed, blade shape, blade angle and bearing system. Generally, the fan speed is indicated on the radiator manual. Generally speaking, 30% of the cooling effect of the radiator depends on the speed of the fan.The power supply is normal, but the motherboard is not receiving power and the power supply fan is not spinning. What is going on?
The power supply is normal, but the motherboard is not powered on. The faulty part is usually the motherboard.
1. To determine whether it is a power problem, first unplug all the cables connected to the motherboard.
Find a paper clip.
Find a set of 24-pin (some are 20-pin) cables on the power supply, and find the green wire and the black wire. There is only one green wire and there are several black wires. Choose one close to the green wire. Just use any of the black ones!
Insert one end of the U-shaped paper clip into the green hole, and the other end into any black wire hole next to the green wire.
After inserting the paper clip, you can now connect the power cord and start powering on.
If the fan of the power supply is spinning at this time, it is basically possible to determine that there is no problem with the power supply.
If the fan of the power supply does not rotate, you can basically judge that there is a problem with the power supply and you need to replace the power supply and test it.
2. After detecting that the power supply is normal, use the power supply and the motherboard to turn on the computer separately. Use a screwdriver to short-circuit the power SW pin on the motherboard.
At this time, the motherboard is powered on and the power supply fan will rotate. Then, Add memory, graphics card, hard disk, and connecting cables at one time until the fault recurs and you can find out the faulty part that caused the motherboard to not power on. If the motherboard still does not power on, then the faulty part is the mainboard.
The welding machine has no display and the fan is not running?
The reasons why the welding machine fan does not rotate are as follows:
1. The temperature does not reach the point where the fan rotates.
2. The power cord of the fan is broken or falls off.
3. The fan has burned out.
4. The fan of the welding machine is not running. Even if it can be welded, it is not allowed to be used.
5. The welding machine is not allowed to operate while sick, including the cooling fan. Poor heat dissipation for a long time will burn the welding machine and even cause an explosion accident.
6, the startup capacitor is broken
If the computer motherboard does not have a CPU, the fan will not spin, even the power supply fan, the graphics card fan, and the power supply fan will not spin. Is this normal? How to solve it? ?
There is no text on the display. Has the memory been stored? The CPU fan must be aligned with the CPU FAN interface. Do not change the sys fan casually. Detach the motherboard's button battery for a minute and then put it back on again. If these still don't work, consider the possibility of a CPU problem. The CPU fan may not work for a long time, which may cause the CPU temperature to be too high and burn out. However, you have to find a way to test whether this is the problem. You can take it to a repair place and ask someone to replace the CPU. Try it.
The motherboard only has cpufan but no sys fan. What should I do with dual fans?
The CPU is connected to the CPU FAN position because the CPU FAN has an automatic speed adjustment function that can automatically adjust the speed to reduce noise when the temperature is low. SYA FAN is a socket for managing the temperature of the north and south bridges. If the motherboard temperature is too high, SYS_FAN fan It will run quickly. You can go to the motherboard BOSS program to adjust the fan speed so that the water pump runs at the appropriate speed.
There is no display when the computer is turned on, and the motherboard does not self-check! But the CPU fan is spinning?
Generally this situation is caused by oxidation or poor contact of the memory gold finger. If you encounter this situation:
1, first unplug the computer power cord and press the power button on the chassis 5-6 times. Release the residual charge on the motherboard.
2, then open the side panel of the chassis, insert and remove the memory slots.
3. Remove the CMOS battery from the motherboard and reinstall it after 1 minute. If your computer has a separate graphics card, it is best to plug and unplug the graphics card. After completing the above operations, power on the computer again. The fault still requires booting using the minimum system method: (power supply, motherboard, CPU memory, graphics card, monitor). At this time, you should normally see the display content, and a prompt such as the hard disk or keyboard cannot be detected will pop up. You can enter the bios, and the buzzer will not beep abnormally. If it is abnormal, the display may not display (or the screen may be blurry) or the buzzer may sound abnormally. (1) Memory problem a. The problem itself. It doesn't work in any slot, nor on other machines. Then the only option is to replace the memory. The buzzer usually makes an abnormal sound. b. Compatibility issues. Other machines can be used, but not this one; or a single cord can be used, but two cords cannot be used. Replace the memory. (2) Monitor/graphics card problem a. Connection problem. Check whether there are broken needles or short circuits. b. The graphics card itself is damaged. c. The display is damaged (very unlikely) b. Motherboard problem. The graphics card slot or related control circuit is faulty. At this time, the only solution is to replace the motherboard.
Can the computer motherboard be converted without a CPU installed?
If the motherboard is not connected to the CPU, the CPU fan will still spin. The CPU is a high-heat device. In order to ensure the safety of the CPU, the fan is usually turned on first.
There are also two types of CPU fans, those with intelligent speed adjustment and those without intelligent speed adjustment. When the motherboard starts up, the BIOS program does not start running, and the CPU is at the highest speed stage. After the BIOS starts running, the speed can be adjusted intelligently. If the CPU is not turned on, the BIOS cannot run and the fan is always at the highest speed.
The above is the detailed content of What should I do if there is no fault light on the motherboard?. For more information, please follow other related articles on the PHP Chinese website!

微星主板bios安全启动怎么开启?1.以华为matebookx、windows10为例。以Z390为例,重启按DEL进入BIOS,按F7进入高级模式,点击进入Settings的选项,再进入TrustedComputing。2.有个安全设备支持(SecurityDeviceSupport),将其改为允许(Enable),TPM设备选择为PTT,设置完成后按F10保存重启。3.以B550M为例,重启按DEL进BIOS后选择左侧的SETTINGS以进入设置界面,同样进入安全选项里的TrustedCom

有很多操作都是需要进到电脑的bios系统进行操作,比如说调整启动项,磁盘模式,cpu参数,刷新bios等等。不过不同的电脑品牌主板的bios设置等界面会有不同,那么如何进入华硕bios?华硕主板bios设置界面又是怎么样的呢?下面小编就给大家分享下进入华硕主板bios设置图解教程。一、如何进入华硕bios1、首先重启华硕电脑,在开机的一瞬间并跳出ASUS的标志界面的时候,马上不断按“Delete”键进入bios界面。2、进入到bios界面后,就可以对bios系统进行设置了。二、华硕主板bios设

在安装系统的过程中,许多网民可能会遇到一些问题,导致重新安装系统的失败。最近,一些网民报告说,他们的sus安装win7找不到引导启动菜单,安装后不能正常引导启动菜单进入新系统。下面的小边教你安装win7后找不到引导启动菜单的解决方案。asus安装win7找不到引导启动菜单的解决方案:1.进入华硕主板BIOS,F7进入高级设置。2.进入启动选项。3.修改CSM(兼容性支持模块)。打开CSM,完全支持非UEFI启动附加设备或WindowsUEFI模式。4.返回修改,修改安全启动菜单。5.修改其他操作

win7怎样进去bios设置呢,用户应用win17的时候如果碰到要进入bios的现象要怎么办呢,最先开机后重启,随后等候系统发生黑底白字时按着del,根据这个方式用户就可以很容易进入bios中,在这儿用户能够设置许多作用,非常的容易且便捷哦,下面就是具体的win7怎样进去bios设置方式介绍。win7怎样进去bios设置1、最先打开电脑以后,点击左下方的菜单栏。2、点击菜单里的‘重启’。3、在重启时,直到显示屏发生黑背景,白字时,就会见到进入bios的方法了,这儿提醒要按照del键。4、不停的按

华硕主板开机怎么进入bios设置?步骤/方式1工具/原料:系统版本:windows7系统品牌型号:华硕无畏14开机的时候按下键盘中的“Del”快捷键步骤/方式2即可进入BIOS界面。华硕主板怎么进入bios?1.启动华硕笔记本2.开机的时候按下键盘中的“Del”快捷键即可进入bios设置3.进入bios的主界面华硕主板进bios?进入华硕主板的BIOS有多种方法,以下是其中的两种常见方法:方法一:打开计算机,当出现华硕主板的logo时,按下“删除”键,直到进入BIOS设置页面。在BIOS界面中,

我们在使用win7操作系统的时候,有的小伙伴们因为一些需要想要把自己的系统换成xp操作系统。那么在这个过程中一些小伙伴们可能就遇到了一些问题。对于win7换xp系统bios怎么设置,小编觉得首先通快捷键进入我们电脑的bios,然后找到相关选项跟着小编进行设置即可。具体操作步骤一起来看下吧~win7换xp系统bios怎么设置1.进BIOSThinkPad和联想VBKEM系列的笔记本进BIOS是按键盘的F1键(部分机型是按键盘组合键Fn+F1,Fn键按住不放,反复按F1键)。2.选择Restart标

有时候我们关机要睡觉了,结果win11关机后外设还亮着灯,非常影响体验,这其实是由于关机后usb接口还在供电导致的,我们只要进入bios设置禁用它就可以了。win11关机后外设还亮:1、首先我们重启电脑,在品牌logo跳出时按下“DEL”进入bios设置。(不同电脑进入bios的方法不一定一样,可以查一下说明书)2、进入后,我们先将语言改到中文,方便操作。3、接着我们进入“高级”设置,打开“高级电源管理”4、然后在其中找到“ErP支持”5、随后将它改为“开启(S4+S5)”6、最后按下键盘“F1

在使用惠普的用户却不少,很多人要进入快启动pe系统进行维护的时候却不知道该怎么设置U盘启动,主要是惠普bios设置U盘启动的方法和平常的方法略有不同,那么,惠普电脑如何U盘启动呢,下面我们来看看惠普bios设置U盘启动的教程,大家快来看看吧。1、首先,将u盘插入hp台式机的USB接口处。2、开机快速断续的按F10键进入BIOS设置界面。3、进入BIOS设置后,将界面切换到“Boot”选项,将光标移到“BootDevicePriority”选项按回车键进入。4、选择“HDDGroupBootPri


Hot AI Tools

Undresser.AI Undress
AI-powered app for creating realistic nude photos

AI Clothes Remover
Online AI tool for removing clothes from photos.

Undress AI Tool
Undress images for free

Clothoff.io
AI clothes remover

AI Hentai Generator
Generate AI Hentai for free.

Hot Article

Hot Tools

Dreamweaver CS6
Visual web development tools

WebStorm Mac version
Useful JavaScript development tools

Notepad++7.3.1
Easy-to-use and free code editor

MinGW - Minimalist GNU for Windows
This project is in the process of being migrated to osdn.net/projects/mingw, you can continue to follow us there. MinGW: A native Windows port of the GNU Compiler Collection (GCC), freely distributable import libraries and header files for building native Windows applications; includes extensions to the MSVC runtime to support C99 functionality. All MinGW software can run on 64-bit Windows platforms.

Atom editor mac version download
The most popular open source editor
