Multiple hard disk interface motherboard

What interfaces do motherboard hard drives generally have?

1. This interface is actually a mini version of the SATA interface. The solid-state drive with this interface is very small, less than 5mm thick, so It takes up very little space and is very suitable for thin and light notebooks. Although the mSATA interface solid-state drive is small, it is not bad in speed. It is basically the same read and write speed as the SATA interface SSD. Of course, this is theoretical.

2. PCLE interface: The PCLE used in Apple notebooks is an SSD that is connected to the PCI-E bus and uses an mSATA interface. Its read and write capacity can reach about 800MBs.

3. Currently, there are four main interfaces for solid-state drives, including SATA, mSATA, M.2 and PCI-E. The specific plug-in method is as follows: SATA is more common, just open the case and insert the hard disk data cable and power cable. The mSATA interface only needs to be inserted into the notebook at an angle and then pressed down.

4. Motherboard hard disk interfaces include: SATA, mSATA, M.SATA Express, PCI-E, etc. The hard disk interface is the connection component between the hard disk and the host system. Its function is to transmit data between the hard disk cache and the host memory.

5. There are seven main interfaces on the motherboard: CPU slot: used to install the CPU. Memory slot: used to install memory modules. Graphics card slot: used to install a discrete graphics card, usually a PCI Express slot. Expansion slot: used to install other expansion devices, such as sound card, network card, SATA card, etc. Power plug: used to connect the power cord.

There are several types of hard disk interfaces on the motherboard

1. The hard disk interfaces on the motherboard include: SATA, mSATA, M.SATA Express, PCI-E, etc. The hard disk interface is the connection component between the hard disk and the host system. Its function is to transmit data between the hard disk cache and the host memory.

2. There are 2 or 4 sockets for connecting hard drives on the motherboard. The specific situation depends on the motherboard configuration. The hard disk interface is the connection component between the hard disk and the host system. Its function is to transmit data between the hard disk cache and the host memory.

3. The hard disk has the following interfaces: SATA interface: This is the current mainstream interface type. Mechanical hard disks are basically this interface. The same goes for the solid-state drive, which adopts a 5-inch design, which is very convenient for people who are accustomed to using notebooks to upgrade.

How to connect two hard drives to the motherboard

1. Look on the back of the hard drive and connect as required: master jumper master slave jumper slave active cable data line blue terminated to the motherboard, in the middle The gray end is connected to the slave disk, and the black end is connected to the master disk. Enter the bios and set both hard drives to automatic "auto" so that the motherboard will detect and recognize the two hard drives.

2. The hard disk can be plugged into the motherboard through the SATA interface. The connection method is as follows: first find the SATA interface, as shown in the figure. Just plug the hard drive into the SATA3 interface.

3. The method for connecting the solid state drive to the motherboard is: if two hard drives are connected to the same hard drive data line, the second hard drive should be set as the slave drive.

How to plug the hard disk into the motherboard

The hard disk can be plugged into the motherboard by connecting to the sata interface. The connection method is as follows: first find the SATA interface, as shown in the figure. Just plug the hard drive into the SATA3 interface.

Socket 1 Socket 2 Insert the solid-state drive. Insert the other side of the small opening into the SATA interface on the computer motherboard. (The interface is near the memory module) Use a screwdriver to secure the solid-state drive. Then, cover the chassis and you're done.

First purchase a solid state drive suitable for your computer. The solid-state drive interface is divided into a power supply port and a data port. The notebook expansion port can be placed on the optical drive position. If it is a mechanical hard drive replacement, the interface can be directly replaced accordingly. After the solid-state drive is installed, boot up and press F2 on the boot interface to enter the "bios" page.

It depends on what interface SSD you buy. For SATA interface, plug it in after the hard disk. How to plug the hard disk, you just plug it into the second plug. M2 can only be plugged into the M2 interface. For PCIE, follow the graphics card. How to insert the graphics card? You can find the second empty slot along the way.

If the interface is sufficient, try to plug the hard disk into the SATA3 interface. In the case of dual hard drives, if you have more than 2 hard drives, it is recommended to plug the main hard drive into the interface with the smallest number. Of course, you don’t have to do this, but you just need to adjust the hard drive startup sequence in the motherboard bios.

The above is the detailed content of Multiple hard disk interface motherboard. For more information, please follow other related articles on the PHP Chinese website!