What is the jumper connection method on ASUS z790 motherboard?

php editor Baicao briefly introduces the ASUS z790 jumper connection method for you: 1. CPU power supply jumper: Insert the jumper into the "CPU_PWR1" and "CPU_PWR2" slots. 2. Chassis panel jumper: Insert the jumper into the "PANEL" slot and connect the power button, restart button and indicator light on the chassis. 3. Fan jumper: Insert the fan jumper into the fan slot on the motherboard to control the fan speed. 4. Storage device jumper: If you are using a SATA hard drive, insert the jumper into the "SATA_MODE" slot and select the "AHCI" mode. 5. CMOS battery jumper: If you need to clear BIOS settings, you can move the CMOS battery jumper from the "CLR_CMOS1" slot to the "CLR_CMOS2" slot and back to the "CLR_CMOS1" slot. The jumper connection method may be slightly different depending on the motherboard model. Please refer to the motherboard manual for specific operations.

How to connect the jumper on ASUS z790?

The jumper connection method is determined according to specific needs. The jumper connection method needs to be determined according to specific needs. The jumpers on the ASUS z790 motherboard are used to set some hardware parameters or functions. Different jumper connections can achieve different settings. For specific jumper connection methods, please refer to the user manual of the ASUS z790 motherboard or the relevant information on the official website. Before performing jumper connections, it is recommended to first understand your own needs and the hardware parameters and functions of the motherboard, then find the corresponding jumper positions according to the manual or official information, and follow the instructions to perform jumper connections. If you are not sure about the specific steps for connecting jumpers, you can consult ASUS official technical support or seek professional help. At the same time, the jumper connection method needs to be operated with caution to avoid incorrect connections that may lead to hardware failure or damage.

Asus motherboard jumper location?

1. The connector pins of the motherboard jumper chassis panel are generally placed near the edge of the lower left end of the motherboard. They are usually double rows of pins. There are about 10 groups in total. They mainly include power switches and reset switches. , power indicator light, hard drive indicator light, speaker and other pins.

2. Introduction If you don’t know which pin to plug in, carefully look around. There are instructions on each motherboard. First look under the pin, if not, look carefully nearby.

How to connect the power supply to ASUS motherboard?

Asus motherboard power connection method

1. Find the connecting cable on the chassis,

2. According to the pin markings on the F-PANEL interface of the motherboard, we connect the connecting cable Just plug it in.

3. You can also insert the power cord according to the instruction manual

How to connect the 13th generation i5 cable of ASUS motherboard?

The wiring method of ASUS motherboard 13th generation i5 is as follows:

1. First, install the motherboard in the chassis and ensure that the screws between the motherboard and the chassis are tight.

2. Insert the CPU into the CPU slot and plug the CPU fan into the CPU fan socket on the motherboard.

3. Install the memory, insert the memory into the memory slot on the motherboard, and install the memory according to the requirements in the motherboard manual.

4. Install the hard drive into the chassis and connect the SATA data cable and power cable. Plug one end of the SATA data cable into the SATA interface on the motherboard, and the other end into the SATA interface on the hard drive. Plug the power cord into the power connector on the hard drive.

5. Connect the motherboard and power supply. Insert the 24PIN power plug and 8PIN CPU power plug on the motherboard into the corresponding sockets on the power supply.

6. Install the graphics card (if required). Insert the graphics card into the PCI-E slot on the motherboard, and plug the graphics card's power cord into the PCI-E power socket on the power supply.

7. Connect the front panel. Insert the power, reset, hard disk LED, power LED and other cables on the front panel of the chassis into the corresponding sockets on the motherboard. Make connections according to the requirements in the motherboard manual.

8. Finally, start the computer to test and ensure that all hardware and cable connections are correct.

It should be noted that when connecting cables, you should connect them according to the requirements in the motherboard manual to avoid connection errors or damage to the hardware.

How to wire the ASUS b760m-k?

The answer is as follows: The ASUS B760M-K motherboard jumper connection method is as follows:

1. Clear the CMOS jumper: Move the jumper cap from the "normal" position to the "clear CMOS" position. Then plug it back into the "normal" position.

2. Turn on the sound jumper: Move the jumper cap from the "disabled" position to the "enabled" position to turn on the motherboard sound.

3. Turn on the serial port jumper: Move the jumper cap from the "disabled" position to the "enabled" position to turn on the serial port on the motherboard.

Please note that before changing jumper settings, be sure to turn off the computer and disconnect the power source to avoid electric shock and other damage. Also, read your motherboard manual carefully to make sure the jumpers are set correctly.

How to connect the jumper on ASUS z690-p?

There are two sets of blue pin holes on the ASUS motherboard, each set has 9 pins. First plug in the corresponding pins, and then connect the interface in the middle of the bottom of the motherboard with a wire. Connect the chassis panel cable to the motherboard, then find the FPANEL socket on the motherboard and insert the corresponding pins to complete the wiring.

How to connect the jumper to ASUS b450m pro gaming?

1. POWER SW power switch, controls the switch of the computer, generally a two-pin design, regardless of positive and negative poles; RESET SW restart switch, controls the restart of the computer, regardless of positive and negative poles; HDD LED hard disk work Indications, etc., show the working status of the hard disk, divided into positive and negative poles, the indicator light will not light up if the connection is reversed; POWER LED power switch indicator light, shows whether the computer is powered on, divided into positive and negative poles, will not light up if the connection is reversed; SPEAK speaker, divided into positive and negative poles, will not light up if the connection is reversed. The negative pole is usually a four-pin interface. If the connection is reversed, there will be no alarm.

2. The distribution of the main parts on the computer motherboard, including the CPU, memory, jumper connection locations, audio, etc.

3. The front USB connection is much simpler, because the chassis connection cable has changed from the original scattered multiple lines to an integrated design, and many motherboard USB pins are modular. The design is fixed in a module, making it easy to find the location.

4. For the connection of the front audio pins, mainstream motherboards nowadays basically use a fool-proof design with one hole left open. Just find the pin and plug it in directly.

The above is the detailed content of What is the jumper connection method on ASUS z790 motherboard?. For more information, please follow other related articles on the PHP Chinese website!