How to set up Xiaomi wifi bridge

How to set up Xiaomi wifi bridge

Xiaomi router bridging method:

1. Xiaomi router acts as a relay.

2. Xiaomi router acts as the main router and other routers act as relays.

1), Xiaomi router acts as a relay.

①Power on the Xiaomi router first, and connect the computer to the wireless network Xiaomi_xxxx.

②Enter the default background management address of Xiaomi router 192.168.31.1 or .miwifi.com in the address bar of the browser. This will allow you to enter the management interface of the Xiaomi router.

③After entering the router settings page, click Common Settings, and then select Internet Settings (this option is usually located at the bottom of the page). On the Internet Settings page, find Wireless Repeater Mode and select the wireless network you want to extend the range.

When solving the problem of areas not covered by wireless signals, we can choose to use wireless repeaters to expand the signal range. First, find the wireless router you want to extend the range and enter the wireless password. Next, find the "One-click wireless relay" option in the wireless settings interface, click and confirm, so that you can successfully expand the wireless signal coverage.

④Complete the last step and restart the router, that is OK!

Of course, just like tradition, this method is too boring. However, Xiaomi router also has a great feature, it supports power supply via USB power supply. This means that you can use a power bank to power the router, no longer restricted by the power strip, and can move it anywhere.

2. Xiaomi router acts as the main router and other routers act as relays.

① Take TP-LINK as an example, log in to the setting page 192.168.1.1

②Enter network parameters-LAN port settings-set the IP address to the same network segment as the Xiaomi router. For example, the default IP address of the Xiaomi router is 192.168.31.1, then set the TP IP address to 192.168.31.2. This setting is to facilitate future login to the TP settings page for management. If you do not make this setting, you will not be able to log in to the TP settings page.

③ Enter the DHCP service - set DHCP to disable, and all IP addresses will be assigned by the Xiaomi router. ③ Enter the DHCP service - disable the DHCP function and let the Xiaomi router be responsible for allocating all IP addresses.

④ Enter the wireless settings, set the SSID to the SSID of the Xiaomi router (can also be customized), and the channel setting is the same as the Xiaomi router (if you are not sure about the channel currently used by the Xiaomi router, you will be prompted when setting up WDS Modify) and check to enable WDS.

⑤Click scan-select the signal point connection of the Xiaomi router, enter the correct encryption type and password of the Xiaomi router to set the connection.

⑥At this point, all the bridging functions are set up. Restart TP to enable all settings! $

How to bridge two Xiaomi routers

After entering the Xiaomi router management interface, find the "Network Settings---Wireless Channel and Strength" option. In wireless channel selection, it is recommended to select channel 11. This is because among the three channels 1, 6, and 11, the degree of mutual interference between them is the smallest. Please do not select the "Auto" option but instead select a fixed channel. This can avoid the problem of being unable to access the Internet due to the failure of the secondary router after the main router is restarted.

2. Reset your router (press and hold the reset button), wait for a while, then click on the lower right corner of the screen, find your router in your available network list, and click "Connect".

3. Select "OK"

4. Enter the pin code of the slave router on the back of the router

5. Enter the network name of the slave router, mine is m4

6. Write down the password of the slave router and click "Close"

7. Enter 192.168.1.1 in the browser, and a router login window will appear. The initial username and password are both admin, and click the "OK" button.

8. After entering the router management interface, find the "Network Parameters---LAN Port Settings" option. In this option, you will see an input box that displays the default IP address: "192.168.1.1".

9. Change the "IP address" to: 192.168.31.x, where x is any number. Just make sure it is not the same as the address of the Xiaomi router. In my example, I chose 31. After clicking "Save", the router will restart. Please make sure to follow the steps above.

10. After connecting the computer to the router AP, enter the router's IP address in the browser, such as 192.168.31.x (where x is the specific address of the router), and enter the router's management interface. Next, find the "Wireless Settings - Basic Settings" option and check "Turn on: WDS", and then select "Scan".

11. After a moment, the scanned ap will be displayed. Select the SSID of the Xiaomi router and click "Connect".

12. Enter the "key", which is the password of the Xiaomi router, and click "Save"

13. Select "DHCP Server - DHCP Service", make sure the DHCP service is not enabled, and then click "Save".

14. Find "System Tools---Restart Router" and click "Restart Router"

15. Connect your phone to the router’s WiFi, enter the password recorded in step 6 to connect, and click Confirm! In this way, your Xiaomi router has successfully completed the bridge setup.

The above is the detailed content of How to set up Xiaomi wifi bridge. For more information, please follow other related articles on the PHP Chinese website!