How to adjust the pressure ratio of Shanxing injection molding machine?

Troubled by the pressure ratio adjustment problem of Shanxing injection molding machine? don’t worry! PHP editor Banana has brought you detailed solutions. This article will delve into how to easily adjust the pressure ratio of Shanxing injection molding machine to help you solve production problems. Read on for step-by-step instructions and expert advice to easily control your injection molding machine's pressure parameters.

1. How to adjust the pressure ratio of Shanxing injection molding machine?

Under normal circumstances, the flow and pressure of the injection molding machine have been strictly adjusted and generally do not need to be adjusted again. In special circumstances, it is necessary to re-adjust the pressure and flow limit control potentiometers on the computer CPU. Inspection method of CNC pressure linear proportional control:

　1. The positions of the four "flow and pressure limit control" potentiometers on the computer CPU unit.

2. The preset parameters are to adjust the four-level injection speed to 50 and the pillow pressure to 00.

3. Start the oil pump motor. When the temperature of the sol barrel reaches the sol temperature, press the manual injection button to make the screw bottom. The oil pressure gauge should indicate a pressure value below 20 kilograms. The pressure minimum control potentiometer can be used to adjust. Turning counterclockwise can reduce the pressure.

4. Preset parameters can be used to increase the pillow pressure by steps. The oil pressure gauge indication should be increased proportionally. When the pressure numerical control value of the pillow pressure reaches 50 or 90, the oil pressure gauge should be within an error of 2.5 kg. If it exceeds the adjustment Minimum potentiometer.

2. What should I do if the computer temperature of Shanxing injection molding machine is different from the actual temperature?

You are talking about the temperature display showing 999 degrees. This is a common problem with Shanxing computers. Is every paragraph 999?

If so, check whether the 44-core wire between the thermocouple board and the motherboard is loose. If not, the temperature control IC in the motherboard may be faulty. Prepare to replace the motherboard or thermocouple board.

After repair, pay attention to check whether the heating coil is leaking. The thermocouple may be over-current, causing the temperature control part of the motherboard to malfunction. Hope this helps.

3. What does the ERR-012 fault code of the Bole injection molding machine driver mean?

You need a photo to verify which driver, Bole also has several configurations

4. The injection molding machine ejector pin is faulty?

Processing method:

1): The ejector limit switch is broken, use a multimeter to check the DC24V line. Replace the ejector pin limit switch.

2): The valve is stuck. Use a hexagonal key to press the ejector needle valve core to see if it can be moved. Clean the pressure valve.

3): The ejector pin limit rod is broken. After stopping the machine, take out the limit rod by hand and replace the limit rod.

4): The ejector switch is short-circuited. Use a multimeter to check the 0 voltage of the ejector switch to ground, and replace the ejector switch.

5. What are the methods to troubleshoot Chen Hsong injection molding machine computer troubles?

Troubleshooting method: MPC has no action when pressing mode lock

1. Check whether the safety door is closed;

2. Check whether the ejector pin vertical proximity switch is in the reset position. The computer has no display (no light) 1. Check whether the 150V voltage of the 150VA transformer is normal; 2. Whether the plugs in the CPC computer are loose. The computer has no display (no light). Check whether the plugs in the computer are loose and whether the ICs are tightly plugged in. , whether the connection between the computer and the I/O board is tightly connected to reset the origin, please press the mold locking (glue injection) key until the alarm disappears (changes to the origin) 1. Press and hold the mold locking (glue injection) button to make the mold locking (glue injection) After the glue) is terminated, keep pressing it until the alarm disappears; 2. Press the function selection key, select the position to "Origin Setting", then open it, press the mold lock (glue injection) key, keep pressing it until the alarm disappears, and then set the "Origin Setting" button. Settings" is closed. Now the mold thickness value is different from the actual mold thickness value. After pressing "Cancel" + "High Pressure Mold Locking" at the same time, press "Up" and "Down" on the displayed screen to select "Original Mold Adjustment Position" to adjust the actual mold clamping size. enter. Press the "Enter" key and then the "Confirm" key. Unable to input or modify data, press Cancel + numeric key "3". If the oil pump motor is overloaded, check the oil pump motor thermal relay (INPUT16). If the mold-adjusting motor is overloaded, check the mold-adjusting motor thermal relay (INPUT17). The computer shows that the rear safety door is closed. Close the rear safety door and Check the limit travel switch of the rear safety door. INPUT1 computer shows that the front safety door is closed. Close the rear safety door and check the limit travel switch of the front safety door. INPUT0 and 1. The mold adjustment exceeds the minimum size. The mold thickness exceeds the minimum capacity. Or check the limit switch adjustment before mold adjustment. The mold exceeds the maximum size, the mold thickness exceeds the maximum capacity, or the limit switch is checked after mold adjustment. When the computer displays the automatic operation of checking the nozzle forward limit, the nozzle forward limit switch is not connected to INPUT3 and the molding module has reached the setting. The molding module has reached the predetermined production setting module. In the manual state, pressing the "Cancel" button to reset the cycle time is too long. The production time exceeds the preset cycle alarm time. Check whether the cycle alarm time (TIM5) setting value has expired. The short computer shows that there is foreign matter in the mold. There is foreign matter in the mold or the high-pressure position and low-pressure time settings are incorrect. Check the mold or high-pressure position and low-pressure alarm (TIM6) when the ejector limit switch fails. When operating automatically, the ejector action exceeds the limit alarm setting time. , check the ejector action stroke or limit alarm time TIM24 mold adjustment count switch failure. During the mold adjustment action, the mold adjustment sensor detects a fault. Check the mold adjustment sensor (INPUT20) for mold opening and locking stroke failure. During automatic operation, the mold opening and locking action exceeds the limit. Alarm time, check the mold opening and locking action stroke setting or limit time TIM24 Troubleshooting method MPC presses the mold locking button without action 1. Check whether the safety door is closed; 2. Check whether the ejector pin vertical proximity switch is in the reset position. The computer has no display (no light) 1. Check whether the 150V voltage of the 150VA transformer is normal; 2. Whether the plugs in the CPC computer are loose. The computer has no display (no light). Check whether the plugs in the computer are loose and whether the ICs are tightly plugged in. , whether the connection between the computer and the I/O board is tightly connected to reset the origin, please press the mold locking (glue injection) key until the alarm disappears (changes to the origin) 1. Press and hold the mold locking (glue injection) button to make the mold locking (glue injection) After the glue) is terminated, keep pressing it until the alarm disappears; 2. Press the function selection key, select the position to "Origin Setting", then open it, press the mold lock (glue injection) key, keep pressing it until the alarm disappears, and then set the "Origin Setting" button. Settings" is closed. Now the mold thickness value is different from the actual mold thickness value. After pressing "Cancel" + "High Pressure Mold Locking" at the same time, press "Up" and "Down" on the displayed screen to select "Original Mold Adjustment Position" to adjust the actual mold clamping size. enter. Press the "Enter" key and then the "Confirm" key. Unable to input or modify data, press Cancel + numeric key "3". If the oil pump motor is overloaded, check the oil pump motor thermal relay (INPUT16). If the mold-adjusting motor is overloaded, check the mold-adjusting motor thermal relay (INPUT17). The computer shows that the rear safety door is closed. Close the rear safety door and Check the limit travel switch of the rear safety door. INPUT1 computer shows that the front safety door is closed. Close the rear safety door and check the limit travel switch of the front safety door. INPUT0 and 1. The mold adjustment exceeds the minimum size. The mold thickness exceeds the minimum capacity. Or check the limit switch adjustment before mold adjustment. The mold exceeds the maximum size, the mold thickness exceeds the maximum capacity, or the limit switch is checked after mold adjustment. When the computer displays the automatic operation of checking the nozzle forward limit, the nozzle forward limit switch is not connected to INPUT3 and the molding module has reached the setting. The molding module has reached the predetermined production setting module. Manually

6. Repair the problem that the manual light does not light up when the computer board of the injection molding machine is turned on?

If you want the digital light to be automatically enabled when the computer is turned on, you only need to set it in the BIOS. Press F2 to enter the BIOS after booting. In the BIOS Features Setup item, there is a Boot Up NumLock Status option: On, Off. This function controls the state of the keypad at startup. If set to On, the keypad will be in numeric state (used to enter numbers) but if set to Off, the keypad will be in cursor control state (used to control the direction of the cursor).

7. Injection molding machine contactor computer

The function and principle of the injection molding machine contactor computer

The injection molding machine is a kind of equipment widely used in industrial production, and in the injection molding machine, the contactor computer is a crucial A component that plays a key role in controlling and regulating machine operation. This article will introduce the function and principle of the contactor computer of the injection molding machine to help readers gain a deeper understanding of this technology.

What is an injection molding machine contactor computer?

Injection molding machine contactor computer is a control device in the injection molding machine. Its function is to control the operation of the injection molding machine by controlling electrical signals to implement operations such as starting, stopping, accelerating, and decelerating the injection molding machine. During the working process of the injection molding machine, the contactor computer can automatically detect and control the current and voltage in the circuit to ensure that the equipment can operate stably and improve production efficiency.

Principle of the injection molding machine contactor computer

The injection molding machine contactor computer controls the on and off of the circuit by controlling the contact and separation of the contacts inside the device, thereby controlling the electrical equipment. When the injection molding machine is running, the contactor computer can automatically control according to the set programs and signals, switch the circuit status as needed, and realize the operation of the equipment.

The role of the injection molding machine contactor computer

1. Control the operation of the injection molding machine: The contactor computer can control the start, stop, speed adjustment and other operations of the injection molding machine according to the set instructions and signals, ensuring that the equipment can follow the predetermined program Stable operation.

2. Protect equipment safety: The contactor computer can monitor the current and voltage of the equipment. Once an abnormality is discovered, it can cut off the circuit in time to protect the safety of the equipment and operators.

3. Save energy resources: By controlling the start and stop of equipment, contactor computers can effectively save energy resources, improve production efficiency and reduce costs.

How to maintain the contactor computer of the injection molding machine?

In order to ensure the normal operation of the contactor computer of the injection molding machine, regular maintenance and upkeep work is required, including:

Regular cleaning: Regularly clean the dust and debris on the surface and interior of the contactor computer, and keep it well ventilated. Check the connection: Regularly check the circuit connection of the contactor computer to ensure that the connection is firm and reliable to avoid failures caused by poor contact. Keep dry: The contactor computer should be kept dry and clean to avoid the impact of humid environment on the equipment. Regular maintenance: Regularly inspect and maintain the contactor computer, replace aging parts in time, and extend the service life of the equipment.

Conclusion

As one of the key components of the injection molding machine, the contactor computer of the injection molding machine bears the important task of controlling and regulating the operation of the equipment. Understanding its working principles and functions is of great significance for improving production efficiency and ensuring equipment safety. Through regular maintenance and upkeep, the good operation of the contactor computer can be ensured, the service life of the equipment can be extended, and the company's production can be provided with strong support.

8. Injection molding machine computer data cable

The importance and selection guide of injection molding machine computer data cable

In the modern production environment, the injection molding machine plays a vital role, and the computer data cable is the normal operation of the injection molding machine. One of the essential accessories. This article will discuss the importance of computer data cables for injection molding machines and how to choose suitable data cables to ensure production efficiency and quality.

The importance of injection molding machine computer data cable

During the operation of the injection molding machine, the computer data cable plays a key role in transmitting data. They are connected to the control system and computer of the injection molding machine, allowing operators to monitor and adjust production parameters to ensure product quality and production efficiency. Therefore, choosing a high-quality, reliable computer data cable is crucial for the normal operation of the injection molding machine.

How to choose a suitable injection molding machine computer data cable

1. Determine the applicable specifications: When selecting an injection molding machine computer data cable, you first need to determine the required specifications and interface type. Different injection molding machines may require different types of data cables, so it is important to ensure that you choose one that is compatible with your injection molding machine.

2. Consider data transmission speed: The operation of the injection molding machine usually requires real-time transmission of data, so choosing a data line with high-speed data transmission capability can ensure the stability of the production process.

3. Choose reliable and durable materials: Since the working environment of the injection molding machine may be harsh, choosing data cables made of high-temperature-resistant and wear-resistant materials can improve its reliability and service life.

4. Pay attention to brand and quality: Choosing data cables produced by well-known brands can provide better quality assurance and avoid production failures and losses caused by poor quality data cables.

5. Consider length and connection method: Choose a data cable of appropriate length according to actual needs, and ensure that the connection method is simple and reliable for easy maintenance and replacement.

Summary

Choosing the right injection molding machine computer data cable is crucial for production efficiency and quality. By considering factors such as specifications, transmission speed, material, brand and connection method, we can ensure the purchase of suitable data cables, improve the production efficiency and stability of the injection molding machine, and thus bring more benefits to the enterprise.

9. What is the fault when the computer of the injection molding machine shows that the thermocouple is disconnected?

It should be that the thermocouple wire at the nozzle position of the injection molding machine is broken.

The nozzle position often opens and closes. Such problems are easy to occur with ordinary quality ones. You can choose better quality screw threads. It would be much better to have a fiberglass sleeve protective cover and a spring protective cover at the back.

10. Faults and repairs of injection molding machine computer ps660bm?

Common action faults and troubleshooting methods of injection molding machines without mold locking a. Completely close the front and rear safety doors;

b. Check whether the safety door limit switch is working normally;

c. Check the ejector pin retreat termination switch;

d. Check the mold clamping electronic ruler and the mold clamping termination switch;

e. Check whether the clamping parameters, speed, pressure, and position settings are correct;

f. Check the mold locking Valve coil

The above is the detailed content of How to adjust the pressure ratio of Shanxing injection molding machine?. For more information, please follow other related articles on the PHP Chinese website!