How to use the fully automatic computer wire stripping machine?

The operation of the fully automatic computer wire stripping machine is cumbersome, and many people are at a loss. PHP editor Zimo hereby brings you a detailed guide on how to use the machine, from starting up, feeding materials to stripping wires, teaching you how to get started easily. If you are also interested in the operation method of the fully automatic computer wire stripping machine, then continue reading quickly!

1. How to use the fully automatic computer wire stripping machine?

The fully automatic computer wire stripping machine is a wire harness processing equipment. Pay attention to three points when using it: Make sure the working power supply meets the requirements of the machine.

Choose to process different cables according to machine performance, otherwise it will cause poor processing and unpredictable machine failure. Please lubricate the tool holder, wire wheel and bearing parts regularly to ensure long-term and stable use

2. Computer Troubleshooting of wire stripping machine?

1. "Err01" appears on the display: The machine will automatically stop after cutting a few wires, and the gap between the outlet pulleys is too large.

Solution: First clamp a wire in the outlet wheel, turn the knob to adjust the gap of the outlet wheel downward until the wire break light at the outlet wheel goes out, then turn down 2 numbers.

2. Press Run once and it will stop immediately and display "Err02": The line section is relatively too thick and the speed is too fast.

Solution: Slow down the adjustment speed and try again; the voltage is insufficient and an independent regulated power supply is required; there is dust on the cutter head sensor or the positioning iron piece of the cutter head sensing positioning plate is displaced, and it needs to be cleaned or the iron plate needs to be repositioned.

3. "Err02" appears when running silently: the fuse is broken.

Solution: Replace and try again. If it breaks again, you need to replace one of the driver boards.

3. How to adjust the pause time of the computerized automatic wire stripping machine?

The pause time adjustment method of the computerized automatic wire stripping machine may vary depending on different models and brands. Generally speaking, you can adjust it through the following steps:

1. Check the manual: First, you need to check the manual of the wire stripping machine to understand the specific operation method and adjustment method. Instructions usually provide detailed instructions and steps.

2. Enter the setting interface: start the wire stripping machine and find the relevant setting interface. These interfaces may be located on the machine's control panel or LCD screen.

3. Find the pause time option: In the settings interface, look for the pause time adjustment option. This will usually be found in the operating parameters or advanced settings of the wire stripper. Some models may refer to the pause time as the "strip interval" or something similar.

4. Adjust the pause time: Select the appropriate pause time according to your needs. This time will determine the length of time the wire stripper pauses after completing one stripping operation. You can adjust it according to actual wire stripping needs.

5. Save settings: After completing the pause time adjustment, follow the instructions in the instruction manual to save the settings. This usually requires pressing the OK key or other designated key.

4. What is the fault of the unstable length of the fully automatic computer wire stripping machine?

1. There may be a problem with the wire feeding mechanism and the wire feeding speed is unstable.

2. It may also be caused by a problem with the setting parameters.

3. There is a problem with the wire feeding clamp, causing the wire feeding length to be unstable.

5. How to adjust the fully automatic computer wire stripping machine if it does not cut or advance?

1. Add engine oil to the active part of the knife edge and try again (generally add oil every 8 hours of operation).

2. Slow down the speed and try again.

3. Check whether the wire specifications are within the allowable range of this model.

4. Is the blade dull?

The incision is tilted when cutting the thread

1. The wire itself is too curved and needs to be straightened.

2. The wire opening is not facing the center of the knife edge. The pay-off frame is stuck, causing the input line to slip.

Some wire cores are too long

6. How to debug the computer wire stripping machine?

The computer wire stripping machine is a machine for processing electronic wires. Its main functions are wire cutting and stripping. The computer wire stripping machine is more convenient to operate because it is controlled and programmed by a computer. Suzhou Xingda Machinery is a company specializing in the production of computers. Wire stripping machine, terminal machine manufacturer, wire stripping machines include XD-515, Just display the parameter settings. For example, the wire length, stripping length, and wire diameter knife value are clear at a glance. We have used their wire stripping machine for 3 years and it still runs well;

7. The fully automatic multi-functional computer wire stripping machine does not peel after stripping. what happened?

The knife edges are not completely overlapped, that is, there is a gap between the two blades when the zero switch senses it. The solution is to adjust the light shield of the zero switch.

8. Troubleshooting for the fully automatic computer quilting machine?

Troubleshooting methods for fully automatic computer quilting machines:

One: The main shaft of the quilting machine is unstable during normal quilting work (the stitch length is unstable);

Two: The speed of sewing during normal work Unbalanced;

Three: The inverter of the computer quilting machine displays CAU;

Four: The inverter of the computer quilting machine displays data that increases and decreases from 50 to 150;

Five: There will be scratches from time to time during normal sewing of the equipment. The surface fabric is broken;

There are several ways to troubleshoot:

1: F6 test spindle speed;

2: The computer quilting machine inverter displays data increase and decrease range of 50~150 per gear or displays CAU ;

3：加電源穩壓器；

九、如何選擇適合自己的電腦剝線機？

電腦剝線機的作用

電腦剝線機，是一種用於剝離電線絕緣層的設備。它能夠幫助使用者快速且有效率地剝離電線，提高工作效率，並減少人力成本。

選擇電腦剝線機的關鍵因素

選擇適合自己的電腦剝線機需要考慮以下幾個關鍵因素：

剝線範圍：不同的電腦剝線機適用於不同規格和材質的電線，需要根據自己的需求選擇剝線範圍合適的機型。 剝線精度：剝線的精確度對於工作品質至關重要，需要選擇剝線精度高、穩定可靠的電腦剝線機。 操作便利性：考慮設備的操作介面友善程度、操作便利性，可以減少培訓成本並提高工作效率。 安全性能：安全性是選擇電腦剝線機的重要考量因素，需要確保設備具備完善的安全保護裝置。 售後服務：考慮設備廠商的售後服務水平，包括維修保養、零配件供應等內容。

常見的電腦剝線機類型

根據其結構和工作原理，常見的電腦剝線機可以分為手動剝線機、自動剝線機和半自動剝線機。

手動剝線機：操作簡單，適合剝線量較小的用戶，但工作效率較低。 自動剝線機：適合剝線量大、對剝線精度要求高的用戶，工作效率高，但價格較高。 半自動剝線機：結合了手動和自動的優點，適合中等剝線量的用戶，性價比較高。

常見品牌推薦

市場上常見的電腦剝線機品牌包括金都、嘉維、恩科等，這些品牌的產品在性能、品質和售後服務方面都有一定的優勢，可以作為選擇的參考。

在選擇電腦剝線機時，需要根據自己的需求和預算，綜合考慮剝線範圍、剝線精度、操作便利性、安全性能和售後服務等因素，選擇一款性價比高、適合自己需求的裝置.

感謝閱讀本文，希望能夠幫助您更好地選擇電腦剝線機，提高工作效率，降低成本。

十、全自動多功能剝線機多段怎麼調？

1、全自動剝線機的使用方法！ 1.線材從進線口穿入，經過進線輪，穿過導管放在刀口上；

2、進線輪間隙調節，透過「進線輪間隙調節輪」調節兩輪間隙小於需剝線材外徑，並確保正常剝線皮；

3、出線輪間隙調節：透過「出線輪間隙調節輪」調節至兩輪間隙小於需剝線材外徑，並調節斷線指示燈在亮和滅的臨界狀態時，再向大的方向旋轉半圈。如還出現線材打節而停機，再將間隙調小一點即可。 2、安全使用注意事項！ 為了確保您能安全與正確地使用電腦剝線機，請在使用前詳細閱讀本使用說明書。 1.為了使機器工作電壓穩定，請使用者選配電源穩壓器，以避免電壓過高而燒 壞該機器。 2、使用時該機器應放置於平坦穩固的表面上操作，以免掉落損壞機器。 3.請勿在靠近電磁場較強的區域內使用該機器，以免對該機器產生幹擾。

4、使用時不得在該機器上面放置任何物品，不得接近腐蝕性的化學物品，務必 保持工作環境乾燥、通風、無灰塵，工作室溫：0–35℃。

5、使用時該機器如果出現不理想的剝線效果或不同程度的故障，敬請閱讀本使用說明書中的故障及排除方法，如果仍無法解決，請撥打我們的技術服務電話諮詢檢修的方法，為了您的安全起見，請勿自行拆卸該機器進行檢修。

The above is the detailed content of How to use the fully automatic computer wire stripping machine?. For more information, please follow other related articles on the PHP Chinese website!