Lenovo computer cannot find hard drive

Lenovo desktop computer prompts Error1962 Hard disk cannot be found when starting up

Check the status of the HDD or SSD. If it is faulty or damaged, you need to replace the hard disk with a new one. Check the status of the SATA cable. If it is faulty or damaged, replace it with a new one. Enter the BIOS setup interface and check whether the HDD or SSD is recognized and whether the boot sequence is correct.

Solution: Unplug all other devices from the computer except the power supply and monitor cable, and restart the computer to see if the fault is repaired. The computer hard drive data cable is loose or damaged. Solution: Shut down the computer and disconnect the power supply, then replug and unplug the hard drive data cable, or replace the hard drive data cable.

Cause of the fault: There are other disk devices such as USB flash drives plugged into the computer. The computer reads these disks when it starts, and no system files are detected on this disk. Solution: Unplug all other devices from the computer except the power supply and monitor cable, and restart the computer to see if the fault is repaired.

What to do if the hard disk cannot be found after partitioning the Lenovo computer hard disk

1. First, on the computer, click on the tutorial tool under the text, as shown in the figure below. Then in the software page that opens, click on hard disk 2 and right-click to create a partition, as shown in the figure below. Then drag the dots to resize the partition, as shown in the figure below. Then click Submit on the left, as shown below.

2. If the hard disk can be viewed in the bios, the main boot sector of the hard disk is usually damaged. You can use the pe system with the DOS toolbox to run the DOS command FdiskMBR to try to repair the hard disk master boot sector.

3. The main cause of this type of failure lies in the connection between the hard drive and the motherboard. When this happens, we try to replace a connection line between the motherboard and the hard drive.

4. BIOS setting, this is one of the very important steps. Otherwise, your USB flash drive cannot boot the laptop into PE.

5. You can check it in BIOS mode. If it is not read, it means the hard disk needs to be replaced.

6. The system does not find or recognize the hard disk after booting. This situation causes the system to be unable to start with a hard disk. Even if the computer is started by other means, the hard disk cannot be found.

What to do if the Lenovo laptop e-disk suddenly disappears

First, you can open the computer management in the control panel, and then check the disk management inside to see if there is still a drive letter for the e-disk exist. If it is there, you can double-click to open the e drive. And after restarting the computer, you should be able to see the drive letter of the e drive again.

Check the data cable connection: If the E drive of an external hard disk or other external device disappears, check whether the data cable connection is stable. Try changing the cable or connecting to a different USB port to see if a connection issue is the cause.

This situation mostly occurs in win10 or above systems. You can enter the command diskmgmt.msc in the run window to quickly open the disk management interface. Check to see if there is an unassigned drive letter, or the E drive and the D drive are merged. You can check whether other drive letters have increased capacity.

What should I do if the Lenovo computer’s solid-state drive does not display?

1. The first step is that when the solid-state drive is plugged into the computer and does not display, you first need to confirm the connection problem. You need to check whether the solid state drive is firmly connected. You can try to re-insert and unplug the hard drive, or replace the data cable to confirm whether it is loose or has a poor connection that prevents the hard drive from being recognized normally.

2. 1. Check the boot tab of the motherboard to see if the bootable device can be in the list. If you see the hard drive, select it, save and reboot. Second, if in the first step, you do not see the hard disk in the list, exit the BIOS. Go back to PE, open DISKGENIUS, select the solid state drive, and check whether the first partition of the hard drive has been activated.

3. The solid state drive cannot be displayed on the computer. It may be because it is not scanned, there is no partition, or the hard drive cable is not plugged in properly. The solution is as follows: right-click this computer and select Properties in the pop-up option box. . Select Device Manager on the page.

The above is the detailed content of Lenovo computer cannot find hard drive. For more information, please follow other related articles on the PHP Chinese website!